Question about 2006 Nissan X-Trail 2.2

Open Question

Removing cylinder head

How to remove cyl head

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head removal on 2005 nissan altima 2.5

CYLINDER HEAD REMOVAL

2.5L Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Posted on Nov 13, 2009

  • 10 Answers

SOURCE: do we need to remove the timing chain to remove the cyl head of a 2005 altima

2.5 Nissan altima I assume the answer is yes and be careful reinstalling I believe that is an intrference engine!

Posted on Nov 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 cyl. has water in oil has been running good, wouldn't heat thought thermostat, pulled dipstick,milky, pulled plugs normal, do not smell antifreeze in exhaust ??


You will need to remove the cyl head and check for corrosion and/or cyl head gasket. Best is to take the cyl head to a reputable machine shop for testing and service.

Jan 11, 2016 | 1990 Nissan Hardbody King Cab

1 Answer

5.7l engine. How should I remove cylinder head?


Remove the exhaust manifold, remove the Intake Manifold then remove the Cyl. Head. Make sure to drain the Coolant first.

Oct 25, 2015 | Chevrolet Cars & Trucks

1 Answer

What to do when there no psi on cyl 4 to get the psi up agan"?"


There are at least three possible reasons for no psi in cyl No 4.
1. Burnt or damaged exhaust valve in that cylinder
FIX Remove head and replace faulty valve
2. Blown head gasket (water mixed with sump oil shows milky on dipstick and steam or water coming out of exhaust tailpipe, radiator water disappears )
FIX Remove head, grind flat and assemble with new gasket.
3. Broken piston rings, or cracked piston or burnt hole in piston.
FIX replace faulty parts.
Squirt some sump oil ( 2 or 3 spoonfuls ) through spark plug hole,
spin motor , and if compression PSI improves then it is rings or piston, if no PSI then it is faulty ex valve !!!

Jun 26, 2014 | 2003 Mitsubishi Lancer

1 Answer

Anti freeze is leaking out of first cylinder tube of spark plug bay and car over heated


Do you mean coolant is entering #1 cyl and when you removed spark plug,cranked eng, coolant came out? If that's the case cyl. head gasket/cracked head is the problem. Also you will need to determine what caused the failure,ie: radiator cooling fan inop, thermostat, low coolant level due to leak,or mileage.

Sep 03, 2011 | 1996 Nissan Sentra

1 Answer

Small water leak from the rear of cyl. head on bmw 318 i 1999 can you get to the problem without removing the cyl. head


U already have a BUSTED head gasket and maybe a WARPED head. The solution would be removal of the head, replacing the gasket and shaving the cylinder head! But if u insist, try RE-TORQUEiNG/TiGHTENiNG the head bolts w/ additional ft/lbs until the desired compression to fix the LEAK. The other one is BUYiNG an additive coolalnt SEALER, have used this ones for emergency, but it will only last for a couple of weeks, and will somehow block the RADiATOR FiNS! At the age of ur car, it needs a NEW GASKET, so that it last for more years! Hope that might help u out!

Nov 17, 2010 | 1999 BMW 318 ti

1 Answer

Would anyone have the torque specks for the head bolts for a 2003 Volkswagon Golf with a 2L engine and I have the timing belt off and need to know where the timing marks are


Cylinder Head Assembly: Specifications
Torque & Tightening Sequence
Tighten cylinder head as follows:
Stage I .......................................................................................................................................................................................... 40 Nm (30 ft. lbs.)
Stage II ................................................................................................................................................................................................. 1/4 turn (90°)
Stage III ............................................................................................................................................................................................... 1/4 turn (90°)

845898e.jpg
_____________________________________________
Timing Component Alignment Marks: Locations
Caution: Incorrect removal or installation of the timing belt can result in damage to internal engine components.
- Turn crankshaft to cyl. 1 TDC (arrow) (Engine with manual transmission shown).
- Turn crankshaft to cyl. 1 TDC (arrow) (Engine with automatic transmission shown).
For complete Timing Belt Removal and Installation information: See: Timing Belt/Service and Repair

6edcba1.jpg
6014b0c.jpg
e1375d0.jpg

Sep 15, 2009 | 2003 Volkswagen Golf

1 Answer

How do you time a 1995 Mercedes C280 inline 6 cyl?


hi,pls. remove the cylinder head cover,try to rotate the crankshaft on ot position,then look the hole 5mm in intake and exhaust sprocket,install 2 pcs. of 5mm pin with align on surface of cylinder head,ot on crankshaft pulley and two sprocket lock in the surface of head ,you have a104.941 engine,ty

Apr 08, 2009 | 1995 Mercedes-Benz C-Class

1 Answer

I purchesed a 2003 engine 3.0fwd online I had it installed the machanic did not change the timeing belt. will this distroy the upper cylinder heads and cause the engine not to start


if the engine jumps time (most likely at start up) it will bend several valves in cyl head. when this happens the engine will not start or run. the effected cyl head or heads need to be removed and reconditioned or replaced. cyl heads probebly ok but valves will be bent.

Mar 27, 2009 | 2003 Saturn VUE

1 Answer

Good info on removing head on 2.2 chev 4 cyl


go to autozone.com, click on engine, click on cylinder head; there are 11 diagrams and detailed instructions on removing and replacing the cylinder head

Dec 15, 2008 | 1998 Chevrolet S-10 Pickup

1 Answer

Remove and Replace Cylinder Head


If you took pictures of the brackets in question I could assist you better. Also there is always chiltons manuals.

Sep 29, 2008 | 2000 Chevrolet S-10

Not finding what you are looking for?
2006 Nissan X-Trail 2.2 Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...