Question about Chevrolet Camaro

Open Question

Shifter cable binding at trans camaro - Camaro Chevrolet Cars & Trucks

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 700r4 not working

Is the fluid level correct.? Might help to change the filter and fluid. does fluid smell burnt.?

Posted on Jun 05, 2009

  • 811 Answers

SOURCE: I have a problem with the shifter binding cable

local mechanic shop, not dealership, buy cable yourself, it could be you can change it yourself

Posted on Sep 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put a 95 s10 blazer trans in my 94 fullsize blazer can it be done and work


If it is binding it may just need the pinch bolt loosened and repositioned to eliminate the binding condition.

If it has to do with Park or Neutral start switch- that is on the column independent of linkage.

If the gear shift indication is off, that is a cable link to the dashboard beneath the trim at the bottom of the dash.

Feb 20, 2012 | Chevrolet Camaro Cars & Trucks

1 Answer

Just replaced shift linkage cable in 97 chevy 4x4 1500 truck. shift lever will go through all gears when manually moved by hand, but shifter on column won't go into 1 or 2. Shifter seems to bottom out on...


Hi, Well those shift cables have a slight adjustment at the trans. When I replaced the cable on my 96 i had to adjust it slightly. But before you adjust it make sure that the cable is routed the same way that it came out, if the cable is kinked or bent in any place it can cause it to bind and not go all the way down. Hope that helps

Dec 09, 2010 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Takes 10 minutes for car to drive forward after placed in drive .No problem in reverse .


First, check your Trans fluid level. The next 3 possibilities are the shifter, shift cable and the valve body.

Have a helper shift the car while you watch the cable end move on the Trans. Or disconnect the cable at the Trans and shift it without the engine running. The action should be smooth and immediate. It is possible for the cable to bind and then release.

If the shifter is binding it will also affect the cable movement. You can try to spray WD40 or a similar moisture fighting lubricate on the cable and inside the shifter mechanism.

If this does not help you are going to need to look at the Trans. About the only thing cheap you can try is a Trans filter change and new Trans fluid. The valve body is the most accessible part of the Trans.

Hopefully your problems will be simple and the shift cable will take care of it. Good Luck on this.

May 25, 2010 | 2003 Ford Focus

1 Answer

My 1999 Chevy Blazer wont go into park


secure vehicle with chocks and set parking brake under vehicle check on drivers side of transmission selector control look at cable for binding or damage the cable snaps into place if looks good remove cable and try to put selector shifter into park[ if it goes in and stays than look back under vehicle and try to match up selector and cable.not reaching and trans selector in park adjust cable and reconnect try shifter for park] -if shifter doesnt go into park than check on dash plastic selector lock may b worn or damaged, if above is fine and selector/shifter is not problem than problem is internal inside transmission park rod damaged or broke good luck and thanks for using fixya

Oct 13, 2009 | 1999 Chevrolet Blazer

1 Answer

I have a problem with the shifter binding cable


local mechanic shop, not dealership, buy cable yourself, it could be you can change it yourself

Sep 12, 2009 | 1998 Kia Sephia

1 Answer

700r4 not working


Is the fluid level correct.? Might help to change the filter and fluid. does fluid smell burnt.?

May 13, 2009 | 1985 Oldsmobile Delta 88

1 Answer

No reverse or 3rd gear (OD) auto trans


check that the throttle cable to the transmission is on it might possibly be that you don't have the cable adjusted correctly

Nov 25, 2008 | 1986 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...