Question about 2013 Lexus GS 350

Open Question

Headlight adjustment beam

Adjusting low beam headlights

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 10865 Answers

SOURCE: how2 remove headlight to replace the low beam bulb on 2001 Lexus

Go to any autozone and they will help you replace it as long as you buy the bulb from them.

Posted on Apr 01, 2009

Ad
  • 10865 Answers

SOURCE: Low beam, driver's side headlight

The low beam bulb needs to be replaced. Go to an autozone store as they will sell you the bulb, and even assist you in their parking lot with installing it.

Posted on May 06, 2009

  • 4 Answers

SOURCE: HID low beam headlight replacement for 2003 lexus es300

The HID bulbs are very easy to change, and can be bought online for much less than from the dealer. Check sites like xenondepot and Ebay for Phillips D2R (for reflector headlamps) HID bulbs and you can replace them yourself.

Posted on Jun 06, 2009

mkv0525
  • 358 Answers

SOURCE: Changing 1996 Lexus LS400 headlight bulb.

you have to remove the head lamp. there are 4 bolts that hold it in. you will have to remove ouyer marker lens first.1 screw on top and pull forward. clips hold lens pretty tight.

Posted on Jun 16, 2009

  • 1986 Answers

SOURCE: How do I adjust headlights on 2005 lexus LS430

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How I adjust headlights on a 1999 grand am?


  • Determine the type of headlights you have on your car. You can only adjust composite headlights if they bolt to adjuster plates. For dual headlights, look on the headlights for four adjustment screws per side. Sealed beam units have interior adjustment screws under the hood.
  • 4 Locate your adjustment screws. On sealed beam units, you may need to remove the trim screws and pull the trim off to reveal the Torx screws.
  • 5 Begin with you headlights turned on to the low beam. Use a Torx screwdriver for sealed beam units and Phillips screwdrivers for other types of headlights.



  • Dec 09, 2010 | 1999 Pontiac Grand Am GT

    1 Answer

    Headlight adjustment ford excursion


    Note: The headlights must be aimedcorrectly. Ifadjusted incorrectly they could blind the driver of an oncoming vehicle andcause a serious accident or seriously reduce your ability to see the road. Theheadlights should be checked for proper aim every 12 months and any time a newheadlight is installed or front end body work is performed. It should beemphad that the following procedure is only an interim step which willprovide temporary adjustment until the headlights can be adjusted by a properlyequipped shop. 1-Identify the exact location of the adjustment screws: a) On halogen bulb style headlights, theadjustment screws are located on top of the housing. b) On sealed beam style headlights, theinboard (vertical) adjustment screw and the upper (horizontal) adjustment screware accessible on the exterior of the vehicle. 2-There are several methods of adjusting the headlights. Thesimplest method requires masking tape, a blank wall and a level floor. 3-Position masking tape vertically on the wall inreference to the vehicle centerline and the centerlines of both headlights. 4-Position a horizontal tape line in reference to thecenterline of all the headlights. Note: It may be 'easier to position thetape on the wall with the vehicle parked only a few inches away. 5-Adjustment should be ,made with the vehicle parked 25 feetfrom the wall, sitting level, the gas tank half-full and no heavy load in the vehicle. 6-Starting with the low beam adjustment, position thehigh 1ntensity zone so it is two inches below the horizontal line and twoinches to the side of the headlight vertical line, away from oncoming traffic. Adjustmentis made by turning the top (sealed beam) or inner (aerodynamic type) adjustingscrew clockwise to raise the beam and counterclockwise to lower the beam. The adjusting screw on the side should beused in the same manner to move the beam left or right. 7-With the high beams on, the high intensity zone shouldbe vertically centered with the exact center just below the horizontal line. Note: It may not be possible to positionthe headlight aim exactly for both high and low beams. If a compromise must be made,keep in mind that the low beams are the most used and have the greatest effecton safety. Have the headlights adjusted by a dealerservice department or service station at the earliest opportunity -

    May 24, 2010 | 2000 Ford Excursion

    1 Answer

    I Have an Audi a4 Quatro 2004 model. Adjust Low Beams?


    There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).

    Nov 19, 2009 | 2004 Audi A4

    1 Answer

    I need to replace and then adjust the headlights on my 2000 Chrysler 300M. How do I replace the headlights, then adjust them.


    Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is 2-3 feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.
    Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. This will mark the center of each beam with a +. The marking will tell you where exactly the headlight beams should be centered from a distance.

    Move the vehicle back about 10 to 25 feet away from the garage door or the wall.

    Keep the headlights on the low beam setting.
    Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed.

    Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.
    Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it.

    Turning the side adjuster screws will adjust the lights to the left or right.

    Continue the adjustments until the center of the light beams are aligned with the tape marks. Then adjust the vertical alignment of both beams slightly below the marks on the wall. This will assure that the lights are tilted slightly downward so they won’t blind approaching motorist.

    The will align bot lights, the high and low sine both are connected to the same headlight!!

    Nov 18, 2009 | 2000 Chrysler 300M

    5 Answers

    How do i adjust my headlingt on a 2001 suzuki xl7


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Nov 14, 2009 | 2001 Suzuki Xl 7

    2 Answers

    How do you make adjustments to a 99 bonneville headlights. Repairs were done to the front end and the headlights don't shine on the road now.


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Oct 01, 2009 | 1999 Pontiac Bonneville

    1 Answer

    Replacing headlights and adjustment


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Jun 02, 2009 | 2005 Chevrolet Monte Carlo

    3 Answers

    How do i adjust the headlight beam on my Subaru Forester X MY06 Model


    on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

    If you only have one nut on each, that will adjust the vertical aim of the headlights.

    If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    Apr 26, 2009 | 2006 Subaru Forester

    1 Answer

    Headlight adjustment for 2006 Infiniti M35


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Feb 04, 2009 | 2006 Infiniti M35

    1 Answer

    Headlight adjustment


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Dec 27, 2008 | 2005 Ford Freestar

    Not finding what you are looking for?
    2013 Lexus GS 350 Logo

    Related Topics:

    30 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lexus Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    ROBERT GARCIA
    ROBERT GARCIA

    Level 3 Expert

    902 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a Lexus Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...