Question about 2005 Toyota LandCruiser Prado

1 Answer

Land cruiser hzj75

Are the front and rear spring shackles different lengths

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 31 Answers

Yes because of the weight of the engine

Posted on Feb 22, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bigg t
  • 640 Answers

SOURCE: 1997 Toyota Land Cruiser rain water leak

check the sunroof drains,they may be clogged they are located on the right and left front of the sunroof.

Posted on Jun 07, 2008

  • 1861 Answers

SOURCE: 1992 toyota landcruiser squeaking

Actually, there are not a places to lubricate, other than the Rzeppa joints (those at the big ball & socket looking things right behind the front wheels). That being said, here is what I would look for if it was in my shop:
Examine the front sway bar bushings. They may be bad or worn. Rocking side to side will move the swat bar. Look at the bar, there are 4 bushings; 2 at each end, and 2 under the center of the vehicle, held in by a "half-moon" looking clamp. Spray WD-40 or something like that on it real good & drive it.
Get back to me if this does not help.

Posted on Sep 23, 2008

  • 1861 Answers

SOURCE: 1995 toyota land cruiser

Your front "ball & socket" joints are in dire need of lubrication. You need to do this:
Take the tires off, and look for a fill plug behind the hub, on the housing, above the ball & socket. Remove the plug, and fill it up with 80-90 gear oil. Replace the plug, do the other side.
What you have is a dry joint, and the clicking noise is coming from the u-joint (actually called a "Rzeppa" joint), inside the ball/socket/hub...a good lubrication will eliminate your condition. Hope this answers your question, please feel free to comment back with any other questions...And, thanks for choosing FixYa.

Posted on Nov 01, 2008

  • 35 Answers

SOURCE: wheel alingment specs for toyota land cruiser

Camber
Left−right error
1°00’ ± 45'

Caster
Left−right error
3°00’ ± 1°

Steering axis inclination 13°00’ ± 45’
Camber, caster and steering axis inclination are not adjustable.
If measurements are not within the specification, inspect the
suspension parts for damaged and/or worn out parts and replace
them as necessary.


INSPECT TOE−IN
Toe−in
(0.08 ± 0.08 in.


This is the only Land Cruiser Specs I could find, hope it helps

Posted on Apr 18, 2009

  • 583 Answers

SOURCE: The front drive shaft has been removed from 1989

very strange thing for any one to do--are you sure he hasn,`t put the front diff centre in the back and the crook one in the front ? is there any axles in the front housing?easy enough to check,put both free wheeling hubs in gear and try to turn the front flange from underneath .I have 2or3 of the front shafts in the shed you can have one of those depending where you are or I can measure one up in the morning , if thats the way you want to go , have alook at what you have got and post an answerto me

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hydrolic suspension is the ploblem so i want to change and i fixed coil spring and shockupsober. so how the coil spring and shockupsober to fixed the rand cruiser 100?


You can easily fit coil springs and struts at the rear. at the front you will have to also change the torsion arms for thicker ones. fit gas shocks front and rear.

Oct 29, 2013 | 2001 Toyota Land Cruiser

1 Answer

Front leaf springs shackles keep folding up and droping the front end


You will need to replace the front leaf springs or have them set and tensioned. This entails a specialist heating and bending the springs to their original shape. While you have the leaf springs out replace the shackle bushes. Depending on your budget now would be the time to buy those Old Man Emu suspension parts you've been eyeing.

Oct 16, 2010 | 1986 Toyota Land Cruiser

1 Answer

How to remove rear axels


Welcfome to fixya.Here is the priocedure if you need anything just go to www.collisionrepairadvice.com
  1. Raise and support vehicle. Support at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 25, 2009 | 1984 Jeep CJ7

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

Dash lights on my hzj75 wont come 1992


is it park lights or ignition lights,if its ignition check the fusible link on the positive battery terminal as they always break

Jun 18, 2009 | 1992 Toyota Land Cruiser

2 Answers

Wheel alingment specs for toyota land cruiser


Camber
Left−right error
1°00’ ± 45'

Caster
Left−right error
3°00’ ± 1°

Steering axis inclination 13°00’ ± 45’
Camber, caster and steering axis inclination are not adjustable.
If measurements are not within the specification, inspect the
suspension parts for damaged and/or worn out parts and replace
them as necessary.


INSPECT TOE−IN
Toe−in
(0.08 ± 0.08 in.


This is the only Land Cruiser Specs I could find, hope it helps

Apr 09, 2009 | 1996 Toyota Land Cruiser

1 Answer

Differetial locks for 94 land cruiser


91-97 Land Cruisers had a factory option for front and rear locking differentials. This is a seperate switch and is usually located to the left of US model Land Cruisers. The center dash button locks your transfer case differential changing your Land Cruiser from all wheel drive to four wheel drive depending if you have ABS or not this button either says ECT or Center Dif Lock. If you do not have the Front/Rear locking differential option then your Land Cruiser has open Front and Rear. Hope this answers your question.

Jan 19, 2009 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
2005 Toyota LandCruiser Prado Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...