Question about Mitsubishi Endeavor

Open Question

Center console removal

How to remove the center console.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: Removal of center tray on Saturn Relay

Remove the seat. Should be some torx head bolt attaching it to the seat.

Posted on Jan 24, 2009

GM Elec
  • 1000 Answers

SOURCE: need instructions on how to remove center console to access electric window switch.

Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.

  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

Posted on May 04, 2009

  • 2 Answers

SOURCE: How to remove center console or where to get the diagram? Thanks Tony

In my 2004 Sierra the console is held in by the seat bolts. You will need a star 16 and 20 to get the seats out. There are 2 bolts that go into the dashboard also. There is a big electrical connection under the console that needs to be unplugged to get it out.

Posted on May 23, 2009

  • 2 Answers

SOURCE: how to remove jaguar center console

As in you want a diagram? Either way, I don't have one but I have managed to remove it. I don't know if this might help but I start off by forcibly removing it by holding on to both sides of the top of the console (where the ash tray resides). Upon removal, I remove the cover of the ash tray by unscrewing two screws on both sides of the cover. These require a cross screwdriver. I then take off the connectors to both of the buttons where the gear lever is. The leather surrounding the handbrake is a bit tricky to remove. Slowly unbutton it then remove the top plastic part; you might lose the little spring that holds the button if you aren't careful. Then open the arm rest. Two Torx screws are located by the pivot point of the arm rest. I'm sorry I can't remember the size (most likely an T8). That's just about it. Hope this helps

Posted on Aug 29, 2009

wfservices
  • 260 Answers

SOURCE: center console disasembly instructions

Base Console, Floor, Ranger, Explorer Removal and Installation

  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

How do I remove the center console of a Isuzu Ascender


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

Feb 05, 2015 | 2006 Isuzu Ascender

1 Answer

How to remove center console from 2008 dodge caliber


Hi Rich, hope you well today here's is the fix you need.


23 - Body/Interior/CONSOLE, Center/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure
248438.jpg 1. Pull back on parking brake (5) to the upright position. 2. Open console door and remove two screws (1) fastening console to rear floor bracket (3). 3. Carefully pry up until the retainers (1) disengage from the center console to front floor bracket (6). 4. Disconnect center console wire connector (2) to instrument panel connector. 5. Remove from vehicle.

Hope this help and have an awesome day Rich.

May 23, 2014 | 2008 Dodge Caliber

1 Answer

Remove the center floor shifter console on a automatic 2005 chevy aveo


The center console needs to be removed, pull the shift plate plastic cover off,
remove two bolts inside the console storage box,
remove the fillips screws that are visible,
the front center storage box also has to be removed,

Feb 26, 2013 | 2005 Chevrolet Aveo Sedan

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

On a 2005 Honda Civic I need to know how to remove the center console cover to replace a burned out bulb for the gear shift.


Detach the clips (A, B) by pulling the center console box (C) up, and removing it from the center console (D).


k42282_21.jpg

  1. Remove the screws (A, B) and clips (C), and remove the center console (D).

  2. Install the console in the reverse order of removal, and note these items


k42282_22.jpg

Dec 17, 2010 | 2005 Honda Civic

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

I am trying to remove the center console of a 2003 chevy impala to install an after market radio. Can someone give me directions please?


There are 2 10mm bolts in the compartment hold of the center console that must be removed. Two similar 10 mm bolts must be removed at the front of the center console, near the driver's and passenger's lower legs. The top of the center console, where the shifter is located, snaps out. With this top piece removed, the cigarette and auxilary outlet can be disconnected. Four more bolts near the shifter bracket need to be removed, and then the console is free. Hope this helps someone. I needed to remove the center console to install a component for a car stereo.

Brian

Jul 06, 2009 | 2003 Chevrolet Impala

1 Answer

How do you remove the center console in a 1982 Mercedes benz 380S


hi,center console or center gear lever cover(wooden console)
  • remove radio,then remove control unit of aircon by pressing down the 2 latch,located in upper edge in radio hole.remove screw in upper part of console
  • remove black cover (look like astray)fold both side,remove screw
  • remove shifting lever
  • try to lift in the console,be careful,sometimes sticky



Mar 21, 2009 | Mercedes-Benz SL-Class Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...