Question about 2002 Ford Explorer

Open Question

What is the slot 41 fuse used for ? - 2002 Ford Explorer

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 ford ranger xlt 4.0 I t I unplugged engine and and main wiring harness to engine fuse 41 atill blows as soon as i replace it what else can i check to find short


OK, its impressive that you unplugged many things tracing a fuse.
The1st thing you SHOULD have done is look up the fuse chart for fuse 41. Its in your owners manual.

Fuse 41 feeds the Oxygen sensor heaters.
You may wanna start by ohms or current checking the heaters, or pulling fault codes and seeing if any particular heater is setting a SHORTED code. Unplugging the heater(O2 sensor) may show you that it stops the fuse blowing and the problem is resistance low in that sensor. If it doesnt fix it, likely you have wiring rubbed through somewhere on the heater circuit. This can be checked by using a diagram and component locations to trace the routing of the heater power line back to the fuse, and finding where it has rubbed through and may be touching ground.

Problems with electrical are often best tackled with information on the system. Print out your diagrams before you start unplugging stuff or you are just adding extra work

Nov 15, 2015 | Ford Cars & Trucks

1 Answer

I have a 2001 ford ranger fuse 41 keeps blowing I have a short some where does anbody know where I should start looking


what does fuse 41 provide power to . look between fuse block and that area of the truck

Nov 15, 2015 | Ford Cars & Trucks

1 Answer

Can i change the fuse number 41 with the fuse 42 in the front fuse box


IF the fuse in 41 is the exact same size as 42.
You can NOT put a 20 amp fuse in a 15 amp fuse position safely. It will work, but may not pop if there is a problem.
Also, if you changed them and the vehicle started to work, than the fuse in one of them has broken. You need to replace it with a new fuse.
Replace it with the SAME SIZE. Not a larger one.

Jan 08, 2015 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

2002 ford explorer fuse #41 in fuses box under


In the power distribution box in the engine compartment : fuse # 41 is a 15 amp fuse for HEGO ( Heated Exhaust Gas Oxygen - sensors ) , VMV ( Vapor Management Valve ) , CMS ? and PTEC ( which I believe stands for Powertrain Electronic Controller )

Aug 30, 2014 | Cars & Trucks

1 Answer

Vito 2006 109cdi. fuse number 41 is blowing (engine fuse)


engine light stays on
the ecu will have fault codes stored to be read
that will point to the cause and a fix of the over load

my best information on a vito if diesel..says
10 amp fuse 41 . glow plugs


you must need the van on the road very badly
30 amp in a 10 amp fuse position can
melt the wiring even a fire


index-ldszvhuomwkbtubxskurqnxk-1-0.jpg

Apr 06, 2017 | Cars & Trucks

1 Answer

Went to emissions testing and failed due to the computer not reading the truck and then took it to a mechanic and he found a blown fuse proceeded to change fuse and now its relaying check gauges where the...


You will need to check all the fuses, sounds like the mechanic knocked a fuse loose when changing the cigar lighter fuse.

Start by pressing down on the fuses around fuse #41.

This would be the 8 to 13 range ( #41 is in an odd location, not by fuse #42 ).

I am going to go with fuse # 12 is knocked loose, that is for the PCM relay coil, which without power to this, part of the truck is dead ( this operated the coil on the PCM relay ), but still start with pressing all the fuses in that area ( take a good look where #41 is at, it is center of the fuse panel, where #42 is at an outside edge ).

Jun 02, 2011 | 2006 Ford F-150

1 Answer

Where's the blower motor fuse?


The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
from overloads. It is just behind the battery under the hood.
Remove the cover and look #36 slot which should be marked.
This is 40amp for the A/c Blower.
http://www.motorcraftservice.com/pubs/content/~WO4MNT/~MUS~LEN/41/04mntog1e.pdf
This is an online pdf file of your owners manual and if you look on page 181-183 it shows pictures.
Hope this helps

Aug 25, 2010 | 2004 Mercury Mountaineer

2 Answers

I REMOVED ALL OF THE FUSES AND RELAYS IN THE ENGINE COMPARTMENT BUT DONT KNOW WHICH FUSE GOES WHERE NOW, THERE ARE FUSED 20A 40A AND 60A


Look at the cover assy. All the positions and values are marked on the top of the cover. The slots NOT used will NOT have terminals in them. It is pretty hard to get it wrong if you just take your time.

I did that once.... removed everything. Learned the hard way.. do it one at a time.

Mar 26, 2010 | 1997 Mercury Cougar XR7

1 Answer

12v cigarette lighter/charger doesnt work which fuse is reponsible for that


It is in slot #41 and is a 10 amp fuse.

Here's a link to the fuse panel diagram which you may want to print and save for the future.

http://autorepair.about.com/library/a/1h/bl402h.htm

Jan 10, 2010 | 2007 Volkswagen Jetta 2.5 Sedan

Not finding what you are looking for?
2002 Ford Explorer Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...