Question about 2006 GMC Envoy

Open Question

Passenger front window will not go up - 2006 GMC Envoy

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

2 Answers

2005 Gmc Sierra 5.3 litter SLT. Wire diagram for passanger side power window. No power to door.


Do the power door locks work for that door ? Does you vehicle have door courtesy lights , turn signals on the mirror ? If your vehicle has these other options an they work , you have power to the door . There is an electronic module inside the door ,called passenger door module ! where did you check for power at , the window switch ! These are computer controlled an you would only see a few volts when pushing the switch !

7

  1. Monitor the passenger front window status in the passenger door module inputs list.
  2. Activate the passenger power switch on the passenger door module in the up and down positions.
Does the window status data parameter change accordingly?
Go to Step 8
Go to Step 15

8

  1. Monitor the passenger front window status in the driver door module inputs list.
  2. Activate the passenger front power window switch on the driver door module in the up and down positions.
Does the window status data parameter change accordingly?
Go to Step 9
Go to Step 16
Operate the passenger front power window in the UP and DOWN directions from the master switch.
Does the passenger front power window operate properly from the master switch?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 5

4

  1. Install a scan tool.
  2. Monitor the window lockout data parameter in the driver door module inputs list.
  3. Activate the window lockout switch to both the On and OFF positions.
Does the window lockout data parameter change state appropriately?
Go to Step 5
Go to Step 16
Your best bet is to take this to dealer or a ASE certified repair shop.

Jun 14, 2015 | GMC Cars & Trucks

1 Answer

Front passenger window only goes up. front passenger door switch or driver door switch only operate window up. all other windows fine.


if you make a fist and hit the door on the inside about the middle of the door card HARD while holding the button and it goes down -you have a bad regulator motor- if that doesn't do anything it may be the swicth in the passangers door but i really suspect the motor-cheers Denny

Nov 03, 2013 | 2000 Ford Expedition

1 Answer

Master switch power window and locks


master switch faulty if other switches works windows and locks.

Jan 15, 2013 | 2006 Jeep Commander

1 Answer

Can I use front window motor for back window?


This is going to sound wrong, but I have been told the window motors will match but not on the same side. For some reason they are crisscrossed. The drivers front matches the passengers side rear motor. The passengers front matches the drivers rear motor.

So basically there are only 2 part numbers for the 4 motors. I was lucky enough to find the exact motor in the identical door I was having to repair on my 1994 Crown Vic. I was thinking to use the front passenger motor for the front drivers motor and thats when I learned about window motors.

Aug 28, 2010 | 1995 Mercury Grand Marquis

1 Answer

Window switch for driver control and passenger switch window


sounds like you have a passenger window motor problem. Try hitting the right door panel hard, down near the speaker opening and pushing the switch at the same time. If it moves, the motor windings are and needs to be replaced.

Mar 26, 2009 | 1999 Mercury Grand Marquis

1 Answer

Passenger electric window


Hi Ethel101
I think that what has happened with your vehicle, is that the master (driver control) switch has become defective....If you have a friend who is good with electronics you may be able to ask for help in getting it fixed....otherwise a new unit is needed.

Best regards

Johngee10

May 31, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
2006 GMC Envoy Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...