Question about 2003 Chevrolet Express

1 Answer

Runs dies I replaced key switch it will run then turn off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

Security has been activated. Do a relearn. You have to have it on a battery charger as it takes about 30 minutes to do. Relearn is= turn the key on (don't start) for ten minutes. Turn it of for 30 seconds. Do this three times. After the third time it should have learn the new key. And will start. If you mess up at any time, you will have to start over from the beginning.

Posted on Jun 08, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: Van keeps running after turning off ignition and removing key

need to check the engine timing and to make sure you have the right octune of fuel in your car.

Posted on Apr 09, 2009

deejones2013
  • 1 Answer

SOURCE: Van keeps running after turning off ignition and removing key

I had the same problem in my 2003 Chevy Tracker. I replaced the ignition switch, not the problem. Replace neutral safety switch, not the problem. The problem was battery acid had leaked onto the wires at the right side of the battery tray and melted and fused them together. Had to get someone to separate each of the 20-30 wires, removed to damaged section and rewire them and tape them. And now the vehicle no longer runs in the off position.

Posted on Oct 17, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to find an electrical disturbance in 1998 ford expedition


Normally this condition is the result of a poor body ground connection. Testing for this can be deceiving. At the static(nothing on) condition, testing can show a good ground. However when a circuit is excited, it has a determined resistance and a set current flow. If the ground connection to this or a branch circuit is loose, corroded, or broken wire. This will allow just enough connection to show as being good, but not good enough to complete the circuit with the required amount of connection when energized.

Nov 30, 2014 | 1998 Ford Expedition

1 Answer

97 sw2 1.9 saturn wont start


You need to check your ing switch if it's starting fine right then when you let go of the key so it;s in the run pos and it dies. check the switch.

Jan 01, 2012 | 1999 Saturn SL

1 Answer

Getting fuel andengine running in start position with key turn key back to run position wont spray fuel truck dies


it sounds like ignition switch is faulty thats why it stalls when u turn back to run

Apr 16, 2010 | 1992 Chevrolet C/K 2500

1 Answer

Engine dies right after starting


The wire from your solenoid valve goes directly to your ignition switch there is no fuse in line. The ignition switch contacts or the plug just behind the switch probably has a bad contact. The switch is easily replaceable, just one screw that holds it in place. They did have a tendency to wear out. Don't forget to check the plug behind the switch, and make sure that there is no immoblizer fitted that can give you the problem.

Jul 28, 2009 | 1983 Volkswagen Rabbit Pickup

2 Answers

1991 Honda Civic starts and Runs while cranking only ,then dies ?


Its the electrical part of the ignition switch.. thats pretty common for a 91 Honda

Mar 11, 2009 | 1991 Honda Civic

1 Answer

97 cavalier was running but just stopped.


Question:
Did you replace the ignition switch or the KEY AND CYLINDER?

These are the only 2 things that can make your engine turn off when you release the ignition switch after starting the engine.

I hope this helps you.
ramonalees.com

Jan 30, 2009 | 1997 Chevrolet Cavalier

1 Answer

My car wont stay running


Does the engine die as soon as you release the key, or does it run for a couple of seconds after you release the key and then die? If it dies as soon as you release the key, try holding the key for a few seconds and see if it will stay running as long as you are holding the key (the starter will make a grinding sound while holding the key but won't hurt anything). If it stays running while you hold the key then dies when you release it, that indicates that the ignition switch is bad.

Jul 01, 2008 | 1992 Honda Accord

Not finding what you are looking for?
2003 Chevrolet Express Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...