Question about Cars & Trucks

Open Question

Troubleshooting pt cruiser p0301 code and p0800 codeshow do I repair them

Pt cruiser 2006 b vin 2.4 non turbo p0301 detenation code came up along with a p0800 code for transaxle lockout How can I fix

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

Ad
Tomballpi
  • 10 Answers

SOURCE: how will not blow on 2006 pt cruiser

1st check fuse. Then see if power is coming to horn. A simple power checker can be found at most auto parts store. It may also have a horn relay. Look up your wiring at cargrus. If you still have problems contact me back.

Posted on May 25, 2009

  • 10 Answers

SOURCE: Horn Solution

The horn is located in the front fenderwell on the passenger side behind the inner fender. You can't see it until the inner fender is taken out of the way.

Posted on Jul 09, 2009

  • 412 Answers

SOURCE: where can I find the crankshaft position sensor on

IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Posted on Jul 14, 2009

  • 7353 Answers

SOURCE: I need a schematic diagram for the radiator fan on

I dont have a diagram, but these have 2 speeds and they are a common problem. the fan will need to be replaced (complete unit)

Posted on Oct 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 PT Cruiser, Touring non-turbo model, which does not have a schrader valve or a fuel pump fuse or relay. How do I depressurize the fuel line to remove the injector rail?


If you don't know the source of the gasoline smell, why would you go to the trouble of replacing the O rings? It would be better to identify the source before jumping into a repair like that only to find out after all that work, it still smells like fuel . you can loosen the fuel line fitting slightly to release pressure. I'd do that on a completely cold engine.

Oct 24, 2016 | 2006 Chrysler PT Cruiser

3 Answers

What is the most popular item goes bad when throw code po882 on a 2006 pt cruiser non turbo 2.4??


This is a code for the 12v relay supply to the transmission. Check the fuses in the underhood relay/fuse box to make sure none are blown causing this code. If all are ok, it will take electrical diagnostics to isolate the source of the problem by checking wiring/control module etc.

Jun 07, 2015 | 2006 Chrysler PT Cruiser

1 Answer

Is there a transmission control relay for the tcm on a 2006 pt cruiser 2.4 non turbo


The is a fuse for the transmission. Label EATX. The TCM is built into the PCM.

Jun 07, 2015 | 2006 Chrysler PT Cruiser

1 Answer

How do i change the turbo motor and put a non turbo motor in a 2003 pt cruiser


Changing out an entire engine is no easy feat. The biggest difference you'll have is with the exhaust system. The non turbo engine connects differently.

Oct 01, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Troubleshooting pt cruiser


a lot of them have pressed on pulleys you may have to rent the tool to pull it off and press it on to the new pump after that 3 or 4 bolt 2 lines

Aug 22, 2014 | Cars & Trucks

1 Answer

2003 PT Cruiser turbo. Has just 67k miles on it. Just began making a low pitched loud whistle sound on acceleration or load/uphill. Gets louder with greater acceleration/load, no decrease in power.


I took my car to Keller's Auto Repair in Gettysburg PA, He specializes in Chryslers. I have 04 Cruiser with 2.4 Turbo that had the same whistle noise, and check engine light on. He found code P0301. The noise was caused by the #1 Cylinder injector O ring. Check them out on facebook. They will help you.

http://www.facebook.com/#!/pages/Kellers-Auto-Repair/158207620880499

Sep 24, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Engine code p0301 just had plugs changed and injecters cleaned


p0301 means cyl2 is miss firing still check plug cables

Dec 03, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Where is the horn located on my 2006 pt crusier non-turbo.


Horn is located on the right side frame rail. pull the inner fender and you will see it.

DC

Apr 06, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Ac problem


please click this link and select the proper option given there and solve it by yourself and get your doubts cleared.

http://www.ptdoityourself.net/tl/tl_indexmain.html

Sep 24, 2008 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...