Question about 2007 Fiat Doblo 1.3

Open Question

Interior door panel sliding door fiat doblo

How to remove interior door panel sliding door fiat doblo to tighten handle

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 345 Answers

SOURCE: fiat doblo 1.9diesel

change the injector seals.....common fault

Posted on Jan 12, 2009

Ad
  • 1 Answer

SOURCE: How to remove the interior door lining on ''Fiat Scudo''

is the lock spinning? are you having trouble unlocking/locking it? you have to fiddle with the keys i found there is one for the doors that fits fine and one for the back doors they are spinning locks and designed that way, Try pushing it in as far as you can to catch. or spinning the lock 180 degrees and pushing. Did the trick for me

Posted on Jun 01, 2009

SOURCE: reset service light fiat doblo

Hi Kev, The safest way to do so, is to have a scan and ask the technician to reset. Regards John

Posted on Jun 30, 2012

emissionwiz
  • 76649 Answers

SOURCE: 2004 1.3 fiat doblo not doing more than 30 miles an hour

Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Posted on Aug 07, 2012

  • 147 Answers

SOURCE: Fiat doblo door open light stays on and doors won't lock

this is the door open light indicator on your instrument panel correct? it thinks the door is open. do interior courtesy lights work? i.e. turn on off when opening doors? check for "normally open" circuit faults in the door switches

Posted on Aug 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the tyre pressure for fiat doblo van?


look on the sidewall of your Tire it will say what the P.S.I. should be....

Feb 27, 2015 | 2007 Fiat Doblo 1.3

1 Answer

How do I remove the rear sliding door interior panel on 2001 Nissan Quest?


Mostly clips, screws hold the handle on and bezel around it has clips that can carefully be pried off.. A door panel tool should be used to enage and pry panel clips off

Aug 22, 2014 | 2001 Nissan Quest

1 Answer

Heater plug indicator on dashboard lights for a couple of seconds then goes out when engine is cold


This is a link to a fiat forum and they will be able to assist you there

http://www.fiatforum.com/doblo/329036-2005-fiat-doblo-1-9d.html

Oct 12, 2013 | 2005 Fiat Doblo 1.9

1 Answer

Fiat doblo door open light stays on and doors won't lock


this is the door open light indicator on your instrument panel correct? it thinks the door is open. do interior courtesy lights work? i.e. turn on off when opening doors? check for "normally open" circuit faults in the door switches

Aug 27, 2012 | Fiat Doblo Cars & Trucks

1 Answer

Reset service light fiat doblo


Hi Kev, The safest way to do so, is to have a scan and ask the technician to reset. Regards John

Jun 30, 2012 | 2005 Fiat Doblo 1.9

1 Answer

How do you replace drives side exeior door handel for 95geoprizm


1) Remove the plug inside the interior armrest and remove phillips screw.
2) Remove armrest and two screws that hold door panel to door frame.
3) Pop the outer cover off the interior door handle.
4) Remove the interior lock knob and remove door panel by popping out tabs connected to door frame and lifting up off of window ledge.
5) Remove the two nuts holding exterior handle in place.
6) Disconnect the L shaped linkage from the handle. The trick to getting the L shaped linkage into the new handle is to feed L shaped metal pole through hole in door where exterior handle was, leaving the lower end of this linkage in its slot.
7) Feed the end of L shaped pole through the plastic 'hinge' in new handle by folding the hinge over and pushing the end of the L through both sides of the plastic hinge at once. slide the lower loop of the plastic hinge down the L shaped pole to secure pole to handle.
8) Place new handle into door and reverse the process to reinstall interior panel.

Hope this helps Tim

Apr 17, 2011 | 1995 Geo Prizm

1 Answer

How do I replace the interior LH door handle 97 Jeep Wrangler?


you will need a t-20 or t-15 torx bit driver to remove 2 screws holding the handle this is all that holds them on, on once you have a replacement handle it is easier to remove 2 lower screws on the door panel and unsnap the door panel to loosen it this will allow space making it easier to reinstall new handle just slide each end into the slot and reinsert 2 screws to not fully tighten until door panel is snapped back in. the panel is held on with clips and can be released using plastic pry tool around door panel edges.

Nov 22, 2008 | 1991 Jeep Wrangler

1 Answer

Side sliding door


The trick is that there is a small clip holding the inside handle in place. Push the panel in and grab it with small needle nose or forceps.

Then remove all the interior panels.

There are seven torx screws holding the intern latch into the door frame, and three interconnecting bars between the outer and inner inner handles.

Once you have the ability to move the inner assemble around you can get to the two metric nuts holding the exterior handle.

The lock assembly is removed by depressing the metal latch on the bottom of the handle assemble after the handle is fully removed.

Reverse and replace and that's it. (don't for get to have extra plastic door panel clips as they will break as you remove the interior panels)

Overall - I would suggest to just take it to the dealer or to a body shop. I'm told they would do it for about $75. I took about 2 hrs to do this and if you are even a bit shaky and drop anything into the door, it is game over. Next time I will do the dealer thing.





Oct 30, 2008 | 2003 Chevrolet Express

1 Answer

Replace side door handle assembly


Remove the snap ring from under the inside door handle and plate (a rag around the base of the handle and a left-right tug on the rag may loosen it, or look under it & pry the snap ring off with a small hook tool

Remove the door lock knob bezel; remove the screw & slide it rearward

Remove the door trim; Remove the two clips; slide a thin, flat wide tool under the panel and pry towards you, there are 8 clips to dislodge

Pull the door trim straight up once all of the clips are loosened.

Easy.

Sep 23, 2008 | 1992 Toyota Previa

2 Answers

How do you repair a gmc sierra 1998 inside door handle


You have to remove the door panel, if you have roll down windows the handle will have to be removed. After panel is removed you have to drill the one rivet that hols the interior handle. slide the handle down and unfasten the rod retaining clip. Please make sure you do not break the clip. Install the new interior door handle, clip and provided fasteners. Try the door before you install the interior door panel, Note the is a good time to lube the window roller and the door mechanism. Make sure to install the water shield to provide the protecting from the elements. Line all the plastic retaining clips and or replace if they are broken. Good Luck.

Jul 22, 2008 | GMC Sierra Cars & Trucks

Not finding what you are looking for?
2007 Fiat Doblo 1.3 Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...