Question about 2003 Kia Rio

Open Question

Replace kia rio 2003 waterpump - 2003 Kia Rio

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 35 Answers

SOURCE: Replace Ignition Coil - Kia Rio 2002

must dismantle all wires and battery...

Posted on Sep 24, 2008

Ad
  • 691 Answers

SOURCE: replacing the starter on my 2005 Kia Rio

1st disconnect your battery (Tools that I needed. 14mm socket for mounting bolts, 13 mm socket and a drop light. You need to jack up the front end pretty high both sides and put jack stands under each side. (extra precaution I put wood under the wheels because I don't like getting crushed. Slide under your car (bring a drop light) Look up and see your oil filter. Now look left and you will see the starter motor (oh yeah there is a pain in the as s bracket in the way) remove that bracket (14mm should be right) and then remove the bottom bolt of the starter (you may need a long socket extension here 8"?) The next set of bolts you have to get from up above that come from the other side. Get your light in there the one on the left side is easiest so get that last. The one on the right side will have a wiring harness running really close to it. Force your 14mm socket onto it with a 4 in extension. Back the bolt off till it spins a free but leave it in the hole. Remove the second one until you hear the unit fall. When putting the two bolts from the other side in, don't reef on them to get them super tight. Save your core so you can get some money back. Good repair manuel will cost 20 bucks, Haynes auto repair at your local auto parts store. good luck

Posted on Oct 21, 2009

Testimonial: "Fast Comeback. I think I will become a member here."

  • 137 Answers

SOURCE: How do you replace a brake light bulb in a 2003

You open the trunk and go to the side that needs the brake light replaced, behind the light is usally 1 or 2 plastic twist bolts, undo then and the whole brake assemble sould come out the turn the light left or right then pull straight out and replace the bulb

Posted on Jan 24, 2010

arauzvictor1
  • 466 Answers

SOURCE: knock sensor replacement

Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Posted on Mar 19, 2010

  • 972 Answers

SOURCE: Check engine light is on for my 2003 Kia Rio. At

my 01 did that and it was the plug wires it bucked real bad
next time it happened it was just sluggish up hills and light would come on. it was the fuel filter it had 255,000 miles on it

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix 2012 kia sorento camshaft sensor


replaced crank and cam sensor [Archive] - Sorento Nation - KIA ...

www.sorentonation.com/forum/archive/index.php/t-913.html

20 posts - ‎6 authors
replaced crank and cam sensors put back together cranked up very rough idle some tapping any ... 12-17-2012, 12:24 AM ... It's a 2006 3.5 Kia Sorrento. ... I found theproblem the SUV has a aftermarket alarm and remote start system I tripped ...

Kia Rio Crankshaft Position Sensor Replacement - YouTube

? 4:44
https://www.youtube.com/watch?v=hihQxMWuSFY
Mar 21, 2014 - Uploaded by Jason Roush
While looking for how to replace a Kia Rio crankshaft positionsensor, ... is on and i have a P0340 code, think this is theproblem? kia rio 2002.

Kia Sorrento/Sedona: 3.5 Litre Engine/Timing Belt/Crank ...

? 20:23
https://www.youtube.com/watch?v=CjaD_zYPrUA
Mar 29, 2014 - Uploaded by JamieJones TheCarMan
Repair and/or Replacement tips for timing belt, crank sensor,cam sensor, water pump and drivebelt ...

Crankshaft position sensor - 2003 Kia Sorento - RepairPal

repairpal.com > Questions > Kia > Sorento > 2003 Kia Sorento


Jan 20, 2016 | 2012 Kia Sorento Base 4dr SUV 2.4L 4-cyl....

1 Answer

Can you clean knock sensor on 2003 kia rio


O2 sensors in general are not "cleanable". If they have failed than they are typically replaced.

Do you have a code for an O2 sensor? If so whats the code?

Feb 09, 2012 | 2003 Kia Rio

2 Answers

Manual user for kia rio hatchback 2003


https://www.kia.com/#/ownerInfo/

Go to kia.com and get the manual downloaded after registering with their site with your information.

Good luck to you.

Jul 21, 2010 | 2003 Kia Rio

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

1 Answer

Kia Rio Timing Belt Issues


Could be sign of a tune up indeed spark plug cables would be first thing to check one could be loose or water may be caught in it

Aug 18, 2009 | 2002 Kia Rio

1 Answer

Kia Rio overheating although everything seems ok


Possible early signs of a water pump problem. A failing waterpump will circulate coolent when the RPMS are high but when you slow down, so does the waterpump, thereby causing overheating.

Jul 04, 2009 | 2001 Kia Rio

1 Answer

2003 Kia Rio RXV. Car does not go into any gear,


Make sure the trans fluid level is correct. It is, Engine off, ck to make sure linkage is working trans shift lever on trans,,,,,,,,good luck

Jun 19, 2009 | 2003 Kia Rio

1 Answer

Proper installation sequence for 2003 kia rio sparkplug wires


this post is listed as 2 years old .there are 5000 un answered kia problems and i just started last week. 2003 kia rio's yours mine and every one else's are blue book valued at about $500.there are not alot of self help out there as with other cars . if you still need help you can try reposting.any way 2 years later your cylinders are # from the left 1 2 3 4 on the side were the wires start each distributer has a corresponding # in white

Nov 01, 2008 | 2003 Kia Rio

Not finding what you are looking for?
2003 Kia Rio Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...