Question about 2006 Suzuki Forenza

Open Question

WHERE IS THE THROTTLE PEDAL POSITIONING SENSOR ON A 2008 SUZUKI FORENZA

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: location of cam position senor

Not a bad job to replace the cam position sensor, it took about two hours cost about $150.00 with oem parts. First remove air filter box,remove plastic spark plug cover. Jack up engine about an inch remove engine mount. Now you can access sensor through a convenient cover that mounts around engine mount bracket extending from engine block.( one ten millimeter bolt) Remove accessory drive belt for a little extra room and replace with new one while you are in there. Just between the two cam gears you will see a torx screw that aligns the switch when in installed. DO NOT REMOVE THIS Just above the torx screw is a reverse torx screw (6 millimeter) Put a shop rag in the access hole to catch the screw just in case you drop it ,( so it does not fall into timing belt cover) Put something "sticky" in the 6 millimeter socket such as gasket sealer to keep from losing screw. remove. Pull switch up from inside spark plug cover and install new one through the same. reinstall 6 millimeter bolt. Switch is self aligning. Reinstall belt, engine mount, air box. Doing this myself probably saved me about $150.00 to $200.00 dollars

Posted on Jun 08, 2008

johnjohn2
  • 5763 Answers

SOURCE: on my 2007 suzuki forenza the check engine light

no such code on that car, auto zone uses global testing which pulls universal codes, so that code means someting different for the suzuki, need to have it checked by the dealer or a shop that has import software, or post the code # and i can translate it into import code, good luck.

Posted on Nov 28, 2009

rockitman187
  • 2559 Answers

SOURCE: 2005 Suzuki Forenza S Oxygen Sensor replacement

You will need to splice in the universal ones.

Posted on Jul 30, 2010

  • 1168 Answers

SOURCE: Where is the crankshaft position

Hello Aldozer.

It is mounted below the power steering pump and behind the AC compressor(if equipped).
Both will need to be removed to access it.
Here is a pic of the engine after they are removed.
kiltylake_8.gif

I hope this helps you towards a good repair.
Thank you for using FixYa.

KL

Posted on Nov 16, 2010

alicantecoli
  • 22095 Answers

SOURCE: Where is throttle positioning sensor

under the dash on the end of the throttle pedal

Posted on Jan 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for a source for a accelarator pedal position sensor for 2008 Suzuki forenza - can you help?


unless you want to pay top dollar , go to a wreckers / junk yard and get a good serviceable unit

Jun 27, 2017 | Suzuki Cars & Trucks

1 Answer

08 suzuki forenza has throttle control but lags a bit put car in gear no throttle control at all


scan it , with a scan tool
it has DTCs,
then get it fixed
or RTM , read the manual, it tells you what to do. why not do that?

on new cars with TBW, throttle by wire, if any of 4 TPS fail to agree
the throttle goes to limphome mode. SCAN it see that?

https://suzukipitstopplus.com/Products/1035-2008-forenza-reno-service-manual.aspx

Aug 17, 2014 | 2008 Suzuki Forenza

1 Answer

P2135 THROTTLE/PEDAL POSITION SENS/SW A/B VOLTAGE CORRELATION


possible causes faulty tp sensor main and sub circuit. electric throttle body assembly faulty or faulty ECM.

Mar 27, 2013 | 2006 Suzuki Forenza

1 Answer

2006 suzuki forenza


P02135 TPS sensor 1 and 2 corelation, You need a scan tool to observe the corelation of 1 and 2,You will have to access the throttle motor and open it by hand.Disconnect the TAC do you have the 5volt reference and make sure you terminal connection are making good contacts

Mar 13, 2012 | Cars & Trucks

1 Answer

Where is the throttle position sensor on a 2007 suzuki forenza


on a 2006 it is on the throttle body at the throttle plate. There are actually three TPS sensors in this configuration. One attached to the gas pedal. One attached to the throtle body And, one located inside the top of the engine block. The defective TPS sensor is removable with four screws. American Suzuki has to be a pain in the *** by selling it only as part of the entire throttle body.

Sep 18, 2011 | 2007 Suzuki Forenza Sedan

1 Answer

The check engine light came on and the dealer says I need a new throttle body. Unfortunatley this part is not under warranty. What will happen if I keep driving with out replacing the part. Is this a...


  • If you don't replace the throttle body, eventually, you will not have a response when you accelerate (press on the gas pedal) Soon, you won't be driving anywhere. You should replace it as soon as you can.

Regards, Tony

May 24, 2011 | 2008 Suzuki Forenza

2 Answers

Where is throttle positioning sensor on a suzuki forenza


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the Intake Air Temperature (IAT) sensor connector.
  3. Disconnect the breather hose from the valve cover.
  4. Remove the air intake tube.
  5. Disconnect the throttle cables by opening the throttle and moving the cable through the release slot.
  6. Disconnect the vacuum hoses from the throttle body.
  7. Disconnect the Throttle Position (TP) sensor and the idle air control valve connectors.
  8. Disconnect the coolant hoses from the throttle body.
  9. Remove the throttle body and discard the gasket.
  10. Remove the TP sensor.
  11. Remove the Idle Air Control (IAC) valve.
  12. Remove the throttle body retaining nuts.
  13. Remove the throttle body.

To install:

  1. Install the throttle body.
  2. Connect the TP sensor connector and the IAC valve connector.
  3. Connect the coolant hoses to the throttle body.
  4. Connect the vacuum hoses to the throttle body.
  5. Connect the throttle cable.
  6. Install the air intake tube.
  7. Connect the breather hose to the valve cover.
  8. Connect the IAT sensor connector.
  9. Connect the negative battery cable.
  10. Fill the cooling system
  11. shinehutt_33.gif
  12. i hope this helps tps is attatched to hrottle body on other side than throttle cable
  13. plz dont forget to vote rep[ly if you need more help

Jan 17, 2011 | 2006 Suzuki Forenza

3 Answers

How do i replace my TPS on a 2006 Suzuki Forenza?


2006 SUZUKI FORENZA RECALLS/DEFECTS & PROBLEMS Access the National Highway Traffic Safety database of 2006 SUZUKI FORENZA recalls and defects found on 2006 SUZUKI FORENZA automobiles. The National Highway Traffic Safety administration is authorized to order the 2006 SUZUKI FORENZA manufacturers to recall and repair vehicles or parts of motor vehicle equipment when its investigation indicates that they contain serious safety defects in their structure, or performance.
Check with your loacol suzuki for recall not sure on this part but it is a common problem
Good luck

Nov 29, 2010 | 2002 Mitsubishi Eclipse

2 Answers

My 2008 Suzuki forenza loses power hesitates and regains power slowly I have had it into the dealer ship and they said it was fixed The car had to be towed back to the dealer ship last week for the same...


I also have a 2008 Forenza. It is currently at the dealership because the transmission failed. I took it to the dealership and asked them to look into it when I got an oil change, they said they found nothing. Two days later, the check engine light was on and the car was severly jerking like it could not catch the correct gear. At first they said it was a sensor, and fixed that. I picked the car up, drove 1 mile, and it started jerking again - needless to say, I went back. They told me it could be the transmission module, but if not, they would have to replace the entire transmission. My advise is to be persistant with the dealership to find your problem or they will continue to pacify you and brush you off.

Mar 31, 2010 | 2008 Suzuki Forenza

Not finding what you are looking for?
2006 Suzuki Forenza Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...