Question about 2005 Ford Ranger

1 Answer

Belt diagram timing

Timming belt replacement and markings

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

I assume 4cyl?

  1. Loosen tensioner adjusting bolt.
  1. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible.
  1. Tighten adjusting bolt to hold tensioner in released position.
  1. Align crankshaft so number one piston is at TDC (top dead center) with crankshaft key pointing straight up and circle on crankshaft sprocket (6306) aligned with notch in engine front cover (6019) .
  1. Align triangle on camshaft sprocket with triangle on inner timing belt cover.
  1. Align diamond on oil pump sprocket with diamond on inner timing belt cover.

    Timing Mark Alignment

belt diagram timing - 5f171ff.gif

Posted on Jul 22, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keemo68
  • 1263 Answers

SOURCE: 2000 ford escort se 2.0L sohc timming belt

the easiest way to help you is you can purchase a repair manual for your vehicle at an auto parts store like napa,Oreillys or auto zone the manuals are around 20 dollars and have all the specifics you will need to do this your self. these manuals have diagrams and step by step instructions. good luck and hope this helps you.

Posted on Aug 28, 2008

honeymokey
  • 3113 Answers

SOURCE: can not find timming marks on cam gears

Ther are none. It takes a tool to hold the cams in place while the valve cover is removed. Get a chilton book from the library.

Posted on Nov 06, 2009

fordfixer
  • 58 Answers

SOURCE: need timming belt marks diagram

Here you go...



d849601.gif

Posted on Feb 28, 2010

  • 122 Answers

SOURCE: diagram for timming belt on 2002 ford focus 2.0ltr

there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Posted on May 28, 2010

Testimonial: "thank you"

  • 70 Answers

SOURCE: need diagram for timming mark set up to install belt

Here ya go, 84775161

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timming belts and OBD2 codes.


Its possible the gears are not on the right marks.
Have you checked cam timing since replacing the second belt ?

Sep 03, 2012 | 2004 Kia Optima

1 Answer

Need too know the timming marks on where to set them at on a 1988 dodge ram 50 2.0 4 cyl


Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Aug 13, 2010 | 1988 Dodge Ram 50

1 Answer

Timming belt marks


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 2001 Volvo S40. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2001/make/volvo/model/s40/2001_volvo_s40_timing_belt_diagram_marks.htm

Mar 05, 2010 | 2001 Volvo S40

2 Answers

Diagram for timming belt on 2002 ford focus 2.0ltr


there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Jan 23, 2010 | 2002 Ford SVT Focus

1 Answer

Timing mark diagram for a 2000 daewoo nubira cdx


here are the timming marks

7a3496b.jpg
e98992a.jpg
the other important thing is to
Rotate the automatic tensioner hex–key tab anti-clockwise until the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch in the timing belt automatic tensioner bracket.
then turn engine over 2 turns and recheck marks and tensioner pointer

Nov 02, 2009 | 2000 Daewoo Nubira

1 Answer

Timing mark location and set up for t-belt, engine broke t-belt, just replaced head assy


TIMMING BELT MARKS
NEED MORE INFO ON ENGINE 4 CYL OR 6 CYL
ALSO IF YOU JUST REPLACED THE HEAD ASSEMBLY MEANS YOU BENT THE VALVES WHEN THE BELT BROKE. TIMMING MARKS ARE DIFFERANT ON MANY MAKES PURCHASE A CHILTON MANUAL FOR THE YEAR AND MAKE OF YOUR CAR THESE MANUALS ARE GREAT AND TAKE THE GUESS WORK OUT OF THE TIMMIMG MARK ISSUE

Aug 22, 2009 | 1998 Hyundai Elantra

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

Replace timing belt on Volvo S60


There is no room for error...... Zero clearance. If off one tooth it can and will bend valves. if you are one that just feels the need to get alittle dirty or just can't pay for the service, then get out your Haynes out and turn to .....Tune up, and look at replacing timming belt. Get a cam gear tool that locks them into place so as that they will not move when u have them lined up. make sure they are lined up with marks as said in book. then make sure crank as well as all marks are lined up acordingly. make sure belt marks are lined up with everything. i would reccomend using a volvo belt though cause it will have all the marks on it.However other company's make good quality belts also at a fraction of the price. So it is really up to you.
Good thing when doing timming belt is to also change out your timming belt tensioner. YES do this it will save you a engine in the long run. it is a moving part that will go bad, it will freeze up and snap timming belt. rip out teeth in thebelt and bend valves. So as a gen rule...When you change timming belt, Change belt tensioner at same time since you cant just change tensioner without changing or getting timming belt off. Remember to use your HAYNES. It is your friend and will save you money in the long run. Good luck... Hope this helps you.

Apr 01, 2009 | 2001 Volvo S60

Not finding what you are looking for?
2005 Ford Ranger Logo

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...