Question about 1992 Audi 100
Take off drivers door panel to get to electric door panel
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I had similar problems with speedos in two 1990 Audi 100s, it was some time ago, but the contacts on the circuit boards on the back of the speedo deteriorate and do not give a good contact. I bought second hand speedos, only to find they had similar problems, eventually it was very easy to fix, I shaved matchsticks to chisel points and pushed them into the circuit boards to add pressure on the contacts and improve connection. After that repair drove the cars for a few years and the problem did not recur. It was a long time ago and I cannot remember exactly where the matchsticks were placed but look for soldered points near the edges of the boards. Regards, Michael
Posted on Dec 08, 2008
SOURCE: electrical fault Audi A4 2002
PRISE OUT THE TRIM PANEL AT THE BASE OF THE ARMREST WITH A FLAT-BLADED TOOL UNDO 2 SCREWS(DRIVERS DOOR) SINGLE SCREW ACCESSIBLE THOUGH THE ARMREST ON PASSENGER SIDE ,NOW GO TO THE BASE OF THE DOOR TRIM UNDO THE SCREW IN THE CENTRE,ONTO THE TOP TRIM NOW ABOVE THE RELEASE HANDLE,STARTING AT THE FRONT EDGE(DOOR HINGE SIDE) CAREFULLY PULL THE TRIM PANEL AWAY FROM THE DOOR TO RELEASE THE CLIPS,THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL,UNDO THE 4 SCREWS YOU CAN SEE,UNHOOK CABLE FROM REAR OF INTERIOR DOOR HANDLE,DISCONNECT WIRING PLUGS SPEAKER ,WINDOW MOTOR CONTROL UNIT AND THERE YOU HAVE IT ..EASY... IF YOU START NOW YOU WILL HAVE IT FINISHED IN 2 DAYS...ONLY JOKING....SHOULD TAKE 1 HOUR..HOPE THIS WILL BE OF SOME HELP TO YOU...LET ME KNOW HOW YOU GOT ON
Posted on Feb 10, 2009
FIRST CHECK THE CABLES THAT RUN INTO THE DOOR BECAUSE THEY CAN GET CUT THOUGH COMMON PROBLEM (JUST WERE THE DOOR HINGES INSIDE RUBBER BOOT.) DOOR PANEL REMOVAL...... PRIZE OUT THE TRIM PANEL AT THE BASE OF ARMREST UNDO TWO SCREWS (DRIVERS SIDE) OR ONE SCREW ACCESSIBLE THROUGH THE ARMREST UNDO THE SCREW AT THE BASE OF THE DOOR TRIM IN THE CENTRE. STARTING AT THE FRONT EDGE CAREFULLY PULL THE TRIM PANEL (ABOVE THE INTERIOR RELEASE HANDLE ) AWAY FROM THE DOOR TO RELEASE THE CLIPS, THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL.UNDO THE 4 SCREWS IN THE TRIM PANEL RECESS NOW PULL THE DOOR PANELAWAY FROM THE DOOR FRAME RELEASING THE RETAINING CLIPS, SOME FORCE WILL BE NEEDED PREPARE FOR SOME CLIPS TO BE BROKEN THEN LIFT THE DOOR PANEL UP SQUARELY NOW YOU CAN EASILY GAIN ACCESS TO ELECTRIC MOTOR.HOPE I WAS SOME HELP TO YOU THANKS STAN
Posted on Feb 23, 2009
SOURCE: Audi A4
Not sure if they've changed it but this is what i do for my 99 a4
First remove the screw in the handle pull, it should be next to where your fingers go.
Pull down on the black piece of plastic and remove the screw form the door
Then remove the screws on either end of the door, one near the door jam on top and one near the other side, same place.
Finally pull up then out and the door panel should come out
Hope that helps
Posted on Jun 17, 2009
Tips for a great answer:
May 11, 2012 | 1992 Audi 100
Jan 03, 2011 | 1992 Audi 100
Dec 03, 2010 | 2005 Audi A3
Jul 01, 2010 | 1993 Audi 100
Mar 11, 2009 | 1994 Audi 100
Mar 11, 2009 | 1996 Audi A6
Feb 21, 2009 | 2004 Audi A4
Nov 22, 2008 | 1992 Audi 100
Jun 20, 2014 | 1992 Audi 100
26 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: