Question about 2001 Hyundai XG300

Open Question

How do I remove the radio from a Hyundai XG300

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: replacing 2001 Hyundai XG300 headlight, how difficult?

1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.



06bdfd0.jpg

Posted on Jun 20, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i remove a belt from a 2001 hyundai xg300

Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the engine splash shield.
  3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
  4. Remove the drive belt from the alternator.
  5. Slowly release the drive belt tensioner.
  6. Remove the drive belt from the accessory drive pulleys.
To install:
  1. Install the drive belt to the accessory drive pulley.
  2. Rotate the drive belt tensioner clockwise.
  3. Install the drive belt to the alternator.
  4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
  5. Slowly release the drive belt tensioner
  6. Install the engine splash shield.
  7. Lower the vehicle.

6a7dc59.gif
Accessory drive belt routing—1.5L engine

09edb85.gif
Accessory drive belt routing—2.0L engines

750e1de.gif
Accessory drive belt routing—2.4L engines

8b223d7.gif
Accessory drive belt routing—2.5L and 2.7L engines

5315739.gif
Accessory drive belt routing—3.0L and 3.5L engine

Posted on Oct 17, 2009

  • 491 Answers

SOURCE: how do you remove the wiper arm of a hyundai xg300

GENTLY PRISE FROM THE BOTTOM OF THE ARM WITH A FLAT HEAD SKREWDRIVER AS YOU DO IT WILL MOVE UP SLOWLY.

Posted on Oct 25, 2009

emissionwiz
  • 75235 Answers

SOURCE: how to locate the antenna in hyundai xg300 2001

it is embedded in the rear glass

Posted on May 17, 2010

Testimonial: "thank you so much"

ZJLimited
  • 17970 Answers

SOURCE: how do i remove the

Sonata, Xg 300 And Xg 350

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the negative battery cable.

CAUTION
After disconnecting the negative battery cable, wait for at least 30 seconds for the SRS module to deplete its stored energy.
1. Drain the cooling system into a clean container for reuse.
2. Remove the heater hoses from the heater housing.
3. Discharge and recover the air conditioning system refrigerant.
4. Remove the suction and discharge hoses from the evaporator assembly. Cap the hoses to minimize contamination.
5. Remove the evaporator drain hose.
6. Remove the SRS module and the steering wheel by removing or disconnecting the following:
Steering wheel-to-SRS module nuts
SRS module from the steering wheel and disconnect the electrical connector


CAUTION
Store the SRS module in a safe place with the front facing upward.

Steering wheel-to-steering column nut
Steering wheel from the steering column

zjlimited_196.jpg

Fig. Instrument panel assembly-Sonata (clock over image for zoom)

zjlimited_197.jpg

Fig. Instrument panel screw locations-Sonata

1. Remove or disconnect the following:
Front and rear console assembly and remove both side covers
Glove box, the center pad cover, the center crash pad and the cassette assembly
Lower crash pad. Remove the console mounting bracket and the center support bracket
Rear heater ducts from the heater housing
Control assembly
Blower speed control actuator connector and the blend door actuator connector, if equipped with semi-automatic temperature control
4 retaining bolts and remove the heater assembly

2. Disassemble the heater housing by removing or disconnecting the following:
Vacuum motor-to-heater housing bolts (2 for each vacuum motor)
Vacuum motor rod end connection and remove the vacuum motors
Heater housing cover clips
Cover and the heater core


To install:

1. Install or connect the following:
Heater core and the cover
Heater housing cover clips
Vacuum motor rod end connection and install the vacuum motors
Vacuum motor-to-heater housing bolts (2 for each vacuum motor)
Heater assembly and attach it to the dash panel with the mounting bolts
Heater control assembly. Connect the ducts to the heater housing
Console mounting bracket and the center support bracket
Lower crash pad and both side covers
Front and rear console assembly


2. Install the SRS module and the steering wheel by installing or connecting the following:
Steering wheel to the steering column
Steering wheel-to-steering column nut and torque to 30-37 ft. lbs. (40-50 Nm)
SRS module to the steering wheel and connect the electrical connector
Steering wheel-to-SRS module nuts
Evaporator tubes, the heater hoses and the drain hose

3. Refill the cooling system.
4. Connect the negative battery cable.
5. Evacuate, charge and leak test the air conditioning system.
6. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.


Hope helps.

Posted on Dec 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to take an alternator out of a 2001 hyundai xg300


Reasonably straight forward, except radiator has to be removed. Stupid design fault by stupid people.

May 09, 2011 | 2001 Hyundai XG300

1 Answer

How do you remove the wiper arm of a hyundai xg300


GENTLY PRISE FROM THE BOTTOM OF THE ARM WITH A FLAT HEAD SKREWDRIVER AS YOU DO IT WILL MOVE UP SLOWLY.

Oct 25, 2009 | 2001 Hyundai XG300

1 Answer

Replacing 2001 Hyundai XG300 headlight, how difficult?


1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.



06bdfd0.jpg

Jun 20, 2009 | 2001 Hyundai XG300

1 Answer

Hi i need to know where my ecu is located on my hyundai xg300 2001!!


It's right here - under the dash in front of the center console. Remove the Driver's side RIGHT kick panel - it's right there.
48e27a1.jpg

Jun 16, 2009 | 2001 Hyundai XG300

1 Answer

How change headlight on hyundai 2001 xg300


Remove the head lamp and disconnect the head lamp connector. 0f7fe9f.jpg Remove three 10mm bolts Unscrew the headlamp bulb CAPS to access bulbs. 5502d76.jpg

Jun 13, 2009 | 2001 Hyundai XG300

1 Answer

Difficulty with replacing fog lamp bulb on 2001 Hyundai XG300


Remove the headlight and put it in from the top.

Dec 30, 2008 | 2001 Hyundai XG300

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...