Question about 2010 Ford Crown Victoria

1 Answer

Dtc codes C1266 HAD WRECK IN FRONT HAS HAD MODULE REPLACED

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Ford Master
  • 442 Answers

Anti-Lock ControlPinpoint TestsPinpoint Test F: DTC C1266Refer to Wiring Diagram Set 42, Vehicle Dynamic Systems for schematic and connector information. See: Electronic Brake Control Module > Removal and Replacement > Anti-Lock Brake System (ABS) Module. TEST the system for normal operation.NoVERIFY BJB fuse 109 (20A) is OK. If OK, REPAIR circuit 483 (RD). If the fuse is not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short. CLEAR the DTCs. TEST the system for normal operation. See: Vehicle > Electrical > Diagrams By Number------------------------------------------------- dtc codes - 7e31ae16-fdd7-4a46-aeb5-da4950e51178.jpg - - Disconnect: ABS Module C135. Measure the voltage between ABS module C135-25, circuit 483 (RD), harness side and ground.
if voltage is greater than 10 volts replace abs module if not
check fuse described in upper section if fuse is bad replace if it blows again you need to check wiring

Posted on Apr 22, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service 4x4 light is on...2000 gmc jimmy...replaced the switch on dash but nothing works..what is my next step to fix issue?


Two speed automatic or is it two speed selectable ? Either case the first thing would be have it check for DTC'S - diagnostic trouble codes . Both are computer controlled .
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error

This for the two speed selectable
The transfer case shift control module normally has battery voltage supplied to it at all times through the battery positive voltage circuit (CKT 40). When the ignition is ON, the transfer case shift control module conducts a self-test to determine if it retains the same memory it had when the ignition was last turned OFF. This self-test indicates whether the RAM standby power supply to the transfer case shift control module pin C6 was interrupted, which would result in clearing DTC's from memory. If the self-test fails the transfer case shift control module sets DTC 1.

You can check codes without a scan tool on this two speed selectable system . Do you know what the DLC is ? Under the steering wheel , connector to plug a scan tool into ?
Important: Check the transfer case shift control module for DTCs. The transfer case shift control module is not a class 2 device. DTCs are displayed on the transfer case shift control switch. Use the following four steps to obtain DTCs.
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes.
DTC 001
DTC 002
DTC 003
DTC 004

Dec 30, 2016 | GMC Cars & Trucks

2 Answers

Rear suspension will deflate but why won't it inflate?


That could work , You mite be able to test the sensor in question with ohm meter . Test the front one an see what the resistance is ,then check the back one. I don't know what it should be with out looking it up in the service info . You could also check to see if the sensor is getting power from the control module , an see if there is a return input to the module .
There are a few DTC'S this able to set !
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTCs Description Source Action B1318 Battery Voltage Low Air Suspension Control Module Go To Pinpoint Test C . B1342 Air Suspension Control Module Air Suspension Control Module INSTALL a new air suspension control module. REFER to Module-Air Suspension Control . SET the front ride height. REFER to Air Suspension Initialization (Clear DTC B2140). CLEAR the DTCs. REPEAT the self-test. B1485 Brake Pedal Input Circuit Battery Short Air Suspension Control Module RERUN On-Demand Self-Test. MAKE SURE that the brake pedal is not pressed. If DTC is returned again, REPAIR brake pedal position (BPP) circuitry. B1566 Door Ajar Circuit Short to Ground Air Suspension Control Module Go To Pinpoint Test D . B2140 Initialization Failure (Vehicle Ride Height Not Programmed) Air Suspension Control Module REFER to Air Suspension Initialization (Clear DTC B2140). C1439 Vehicle Acceleration EEC-V Circuit Failure Air Suspension Control Module Go To Pinpoint Test E . C1724 Air Suspension Height Sensor Power Circuit Failure Air Suspension Control Module Go To Pinpoint Test F . C1726 Air Suspension Pneumatic Failure Air Suspension Control Module Go To Pinpoint Test G . C1760 Air Suspension Height Sensor High Signal Circuit Failure Air Suspension Control Module Go To Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test I . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test J . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test K . C1830 Air Suspension Compressor Relay Circuit Failure Air Suspension Control Module Go To Pinpoint Test L . C1917 Steering Electronic Variable Orifice (EEVO) Out-of-Range Fault Air Suspension Control Module Go To Pinpoint Test Q .
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Nov 06, 2015 | 2002 Lincoln Navigator

1 Answer

I get codes or DTC's that i have no idea what would cause them? IPC 04610, IPC P1610, IPC U1255, AMC B1348, SDM U1255, IRC U1255


OBDII Code U1255 CADILLAC Lost Communications HelpForCars net P1610 Cadillac how to repair
DTC B1348 Very Low A/C Refrigerant Pressure
DTC U1255 Serial Data Line Malfunction
The class 2 serial data line communicates information between the modules. Each module connected to the serial data line is assigned a recognition code, or address. This code is used in order to identify which modules are communicating. Modules communicate with each other by periodically sending state of health (SOH) messages. When the ignition switch is in RUN, each module that is communicating on the serial data line sends an SOH message every 2 seconds. This ensures that the system is operating properly. At key on, most modules must learns the initiation data from other modules on the serial data line. When a module requests initialization data from another module, and that request is not acknowledged after 5 seconds, the module stores class 2 initialization error DTC U1255.
Conditions for Setting the DTC
?€¢
The module does not receive required initialization data on the class 2 serial data line. The module retries the request for 5 seconds, and then sets DTC U1255.


?€¢
This DTC only sets if DTC U1300 or U1301 are not current


Attempt to establish communication with all of the modules using a scan tool.
Does the scan tool communicate with all of the modules?
--
Go to Step 3
Go to the appropriate diagnostic system check for the module that is not communicating

May 12, 2015 | 1999 Cadillac DeVille

1 Answer

2000 chevy siverado z71 4x4 not working


Yes we can ! With the light on and or flashing , DTC'S - diagnostic trouble codes are stored in the 4X4 control module . Have the codes check , not at auto zone or any other parts stores . There code reader tool will not pull this codes . Need to take to a qualified repair shop . Testing also needs to done , not guessing an throwing parts at it . This 4X4 system can set a number of codes .
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error

DTC C0387 Unable to Perform Shift
Circuit Description
The transfer case encoder is a switch that converts a shaft position, representing a mode or range position, into electrical signals for use by the transfer case shift control module. The encoder houses 4 Hall effect sensors that are used for channels P, A, B, and C. These sensors provide a path to ground, when a magnet, (part of the Motor Encoder), passes over them.
The transfer case shift control module supplies an 8 V reference and a ground circuit for the encoder hall effect sensors to function.
The transfer case shift control module supplies current limited 5 V on all the channels, thus as these channels are pulled to ground, the module can interpret the location of the transfer case shift position.
This DTC detects that the transfer case is unable to successfully complete a shift to a requested mode or range.

May 07, 2017 | 2000 Chevrolet Silverado 1500

1 Answer

2006 ford crown vic abs code b1596


B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

Jan 14, 2013 | 2006 Ford Crown Victoria

1 Answer

Abs light code c1266


need to take it in and diagnose

May 07, 2012 | 2002 Jaguar X-Type

1 Answer

4x4 not working on my 2002 chevy blazer ls 4.3l replaced the in dash switch and the tcm and the encoder motor what eles can be the issue when it went out it clicked when i switched into 4x4 then down the...


Is the switch lit up , light flashing ? Did you have the system checked for DTC'S - diagnostic trouble codes . Should have had this done before replacing parts . TCM ? your replaced the transmission control module ? Or the transfer case shift control module ? If no codes ,check B+ power and grounds for the control module . Find a wiring diagram so you know which wires are what etc.....Videos on youtube on basic automotive electrical testing , testing inputs an outputs for control modules . This system can set a number of codes !
DTC B2725
DTC C0300
DTC C0305
DTC C0308
DTC C0309
DTC C0310
DTC C0315
DTC C0323
DTC C0324
DTC C0327
DTC C0362
DTC C0367
DTC C0374
DTC C0376
DTC C0387
DTC C0550
DTC C0611

The front axle control circuit consists of a Front Drive Axle Clutch Solenoid which is electronically controlled by the transfer case shift control module. This solenoid opens and closes a vacuum control valve allowing vacuum to apply and release a clutch pack inside the front axle housing. The transfer case shift control module determines whether or not the clutch pack has been applied or released based on a signal from the front axle switch mounted on the front axle housing assembly. The front axle is normally locked or engaged during AUTO 4WD, 4WD HI, and 4WD LO modes. The front axle is unlocked or disengaged only during 2 HI or neutral modes.

The NVG 236/246 transfer case features a 4 button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp will continue to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has been engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position will remain ON constantly.

The NVG 233 transfer case features a 3 button shift control switch, located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch, to determine if a new mode/gear position has been selected. At a single press of the transfer case shift control switch, the lamp of the new position begins flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position remains ON constantly.

Which 4X4 system does your's have ? Three or four button ?

Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
How to Use Multimeter to Troubleshoot Common Problems
Electric Testing Techniques You Need to Know


Jul 04, 2017 | 2002 Chevrolet Blazer

1 Answer

There are 4 codes I need to know about P0810, P1132, P1618, and P1633, 2001 Volvo V-70 24T


810 neutral check, incorrect connection
  • Check the transmission and control module connectors. Check for contact resistance and oxidation according to Checking wiring and terminals. Permanent faults
  • 1132 front o2 sensor signal too high
    1618 dtc is in another module
    Volvo does not provide information regarding DTC P1633 for many of their models.
    However, it has been reported that various Volvo engine control modules will produce this code. The code is associated with a missing or inaccurate vehicle speed signal from the ABS control module and may be accompanied by DTC P0722 or P1618.

    Possible causes:
    - Defective vehicle speed signal to the ABS control module
    - CAN connection problem
    - Defective ABS control module
    - Defective engine control module

    Manufacture codes associated with this P code may include ECM-510f, 530d.

    Mar 28, 2010 | 1998 Volvo V70

    1 Answer

    ABS light permanantly ON. recommend replace ABS module $$$$$$$$$$


    I would go with the ABS module, if the shop is wrong make them fix what the real problem is for free, is this a Jag dealer?

    Dec 11, 2008 | 2002 Jaguar X-Type

    Not finding what you are looking for?
    2010 Ford Crown Victoria Logo

    561 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...