Question about 2000 Chrysler Town & Country

1 Answer

Lft break light will not work replaced bulb and checked fuse what would be next

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 46 Answers

Was the original bulb burned out? If so, check to make sure you have the correct replacement bulb. If the original bulb was ok then you have a wiring issue. Check all the connections to make sure they are good and clean. If no luck then trace it down with wire peircing probe for voltage continuity.

Posted on Jun 18, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 166 Answers

SOURCE: tail light don't work

Check to see if you have a good ground in that location and that none of the wires are kinked, broken or have come loose. Also check the connections and make sure they are clean and dry....if there is any corrosion clean it off and make sure you have a nice tight connection. I would start where the wires for the rear lights branch off fom the main wiring harness; since you have no lights in any of your rear lights the problem, most likely is there. You should also check to make sure you are getting power to that part of the wiring harness; you can buy a amp tester at the local auto parts store which has a small light that turns on if your getting power there. Good luck!

Posted on Aug 25, 2009

  • 6 Answers

SOURCE: i have changed the break

Without knowing the exact year of the chrysler, I will only suggest some diagnostic ideas. One thing to remember is that Chrysler vehicles use the signal switch that is located in the steering colum to channel power to the rear brake lamps. The signal and break light elements are the same and the power supply is turned on and off as required using the signal switch as well as the break switch. Check the power supplies coming out of the steering colum. There is a connector in the lower region of the steering colum that will allow a power supply check. You may have to include more vehicle information on your next diagnostic request.
Cheers.

Posted on Feb 21, 2011

  • 118 Answers

SOURCE: just replaced break light bulbs but light is still

Do you have an owner's manual? There's usually a diagram for the fuse boxes in the manual. Another way is with an inexpensive fuse tester and testing each fuse. If you have a multimeter, you can test for continuity of each fuse. If the meter zeros out the fuse is blown.

Posted on Feb 23, 2011

pied
  • 195 Answers

SOURCE: Have changed the bulb for my license tag, but light still won't come on. Could this problem be a fuse? What do I check next?

Use a test light to check for power to one side of the lamp. If that is the only light out it probably isn't a fuse, but it is worth checking it anyhow. You might have to look for a broken wire in the trunk.

Posted on Dec 22, 2011

little_shaws
  • 493 Answers

SOURCE: 2007 pt cruiser both break lights are out

Bulbs.

Posted on Nov 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda Accord 2006 turning signal not functioning


First check both front and rear lft side bulbs. Then, I would check the signal relay. I think it is under the dash one the left side. Here is want your are looking for. A new one cost about $12-$15 at most parts stores. Last I would suspect the signal switch assembly on the column. (Perchance you have a trailer hitch plug? If so look there too)

j
uploadswith image12_12_2013_2_15_10_am.jpg

Dec 12, 2013 | 2006 Honda Accord

1 Answer

1987 dodge d150 break lights


get yourself a tester to see if you are getting power to the light socket, have someone push on the brake petal and use the tester to check for power. If no power, you have a broken wire somewhere between the rear lights and dash [fuse panel] check for corrosion in bulb socket. try to find the wire along the frame to the rear lights for any breaks in the insulation. electrical is one of the hardest problems to solve, good luck.

Mar 12, 2013 | 1987 Dodge D150

1 Answer

2006 Chevrolet Colorado,only left front turn signal works,not even hazard are working.


first check the brake light fuse it powers the rear bulbs.
remove and verify that all bulbs are working. note the wire colors going to the bulbs. replace as needed.
next check the turn signal switch. if broken replace.
sometimes switches break on the inside so measure from the power lead to the outputs. The wires going to the bulbs. easy because they are on the bulbs you checked.
if you have towing package there will be a connector to hook up lights on the trailer. Inspect for bare wires or cuts in the insulation.
good luck

Feb 21, 2013 | 2006 Chevrolet Colorado

1 Answer

Passanger and third break light don't work, new bulbs and fuses installed. what should i check next?


I would check the turn signal switch first. The brake lights may go thru the switch depending on the configuration.

Aug 16, 2012 | 1992 Honda Accord

2 Answers

Right brake light does not work when press the pedal but all 3 bulbs light up when locking or unlocking car so to me bulbs are good is this a fuse?


If it were a fuse issue, neither brake light would work.

The alarm may be connected to running lights and not the brake light, I'd simply swap bulbs lft to right, if the problem follows, new bulbs before worrying about chasing wiring problems.

Hope this helps.

Feb 18, 2011 | 2006 Pontiac Torrent

2 Answers

Brake lights not working, fuses, bulbs, pedal switch all new. Center brake light in window is working.


First check the ground on the brake lights. Make sure it is connected and not rusted. Next use a meter and check the voltage of the hot wire. If no power check for a break in the wire and or replace the wire back to the fuse block.

Feb 09, 2011 | Saturn SL Cars & Trucks

1 Answer

Toyo dyna 92 break lights not working , is there a fuse for this or is it hard wired bulbs ,work fine , ?


There is a fuse for the brake lights. Check fuse and replace if blown. If the fuse is not blown, check the bulbs themselves. If the bulbs are good, then the next step is to replace the brake light switch located under steering column attached to brake pedal rod.

Feb 16, 2010 | 1992 Toyota Xtracab

1 Answer

Replaced 2 head lght bulbs/does not work


Most Likely The Headlight Switch, Fuse if they are there on this Modle They are Seperated Lft-Rt

Feb 13, 2009 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...