Question about 2007 Ford Bantam 1.3i

Open Question

Ford bantam heater

Heater switch on by it self if car is started while hot

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: HEATER DOES NOT STAY HOT IT STARTS THEN IT GOES COLD

Check radiator fluid level. The heater core sets higher than the engine. If fluid gets low, air bubbles will go to the highest point. The heater core. Check temperature guage. Is engine warming up to normal range? If not change the thermostat. Also check radiator cooling fans with engine warm.
On my car if I set the heater control on anything other than "vent" both cooling fans come on and the engine will not warm up. (still haven't figured that one out) I just run the heater in "vent"

If heater warms up when engine is held at high idle(2000rpms) then cools down at idle, you most likely have air traped in the system.

Posted on Oct 11, 2008

chazman05
  • 48 Answers

SOURCE: 1996 ford contour gets hot , no hot heater or temp guage movement

Is your temperature gauge working now? That is of more concern then your heater as you wouldnt know if your engine was overheating until its too late. Your heater core could be clogged, they get clogged quite easily. You can flush them or replace. The part is inexpensive but on some models you have to take out dash to replace them, but on other models it only takes about 30 mins and a few bolts.

Posted on Dec 17, 2008

pippall
  • 1486 Answers

SOURCE: heater blowing hot all the time

Change the heater contol switch.They are a big problem with the fords.Fiesta and Ka.

Posted on Jul 13, 2009

maadgar
  • 44 Answers

SOURCE: 2003 Ford F250, the heater does not blow hot air

check the heater temp. control pot under the hood, inline on one of your heater hoses, it may be sticking causing hot water to only get to your heater core when the engine is at high r.p.m.s

Posted on Nov 14, 2009

jturcotte
  • 7762 Answers

SOURCE: I have a 2001 Ford Taurus with heater issues.

No, there is no valve in your car. The likely problem is a clogged core. Would you like instructions for replacing it?

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater does not switch off.


Sorry, my US automotive database won't have any info on your vehicle. Maybe somebody else can find that info for you? My thought would be to pull fuse/s for hvac system till you figure out the problem?

Mar 14, 2016 | 2005 Ford Bantam 1.3i

1 Answer

My 2004 bantam pickup with the 1600 rocam engine has got a problem with the heater staying on even on cold setting.I already replaced the heater valve.Assistance would be appreciated.The heater cant be...


Check your hot and cool trim door or flap under the dashboard, the stepper motor that controls it sometimes either gets jammed or just wears out and stops working or if you won't need the heater you can put a valve in the input and output hoses to the heater core and eliminate the hot air and have it accessible whenever you need it?

Mar 07, 2015 | Ford Bantam Cars & Trucks

1 Answer

Hissing noise from reservoir on ford bantam 2009 1.6i


air in the system .put your heating on full .to bleed the heater.remove the expansion bottle cap .run the engine push in the hose from your radiator with your fingers to get the air out your bottle and replace your cap.

Dec 18, 2013 | 2005 Ford Bantam 1.3i

1 Answer

Ford bantam does not start


Check the reset switch near yo icu. reset it if off

Mar 16, 2013 | 2005 Ford Bantam 1.3i

1 Answer

1993 ford escort heater blowing cool


heater core cloged, get car hot check heaterhose going into heatercore should be two inch thick hoses going into the heatercore, underhood against firewall pasenger side, after hot while running heater on, chech to see if both hoses r hot, if one is cold,that means there is a restriction in the heatercore, sometimes on older cars there is a external valve run by a vaccume hose, or cable, thats fixed in with the heater hoses , sometimes this valve jams and can be manually switched.

Dec 16, 2012 | 1993 Ford Escort 4 Door

1 Answer

No Heat, fan works engine is at temp.


Check to see if both heater hoses are hot when the engine has heated up and the heater is running.

You have 2 possibilities. One is that water valve is not opening and the heater core is cold, the second possibility is that the heater core is hot and the ductwork under the dash is not switching the flaps to give heat.

If both heater hoses are hot it means the heater core is hot and the interior ductwork is not channeling heat. You would then need to replace a movement valve or motor to switch the flaps in the ductwork.

Sometimes with the high priced options, there are self-diagnostics in the control panel of the heater. You would need someone to initiate the sequence and let the self-diagnostics pinpoint the bad part. Otherwise you need to dive under the dash and troubleshoot.

Feb 12, 2012 | 1995 Buick Regal

2 Answers

Ford courier 1.8 diesel van, blower works, but no heat comes into the van when heater turned on


ford courier workhorse ,great van ---right when engine is hot feel the hoses that run into the heater ,also it could be the heater core was leaking and someone has joined the hoses together .if the hoses are connected and they are hot then ,try removing them and then flushing the heater with a hose pipe

Nov 29, 2009 | 2000 Ford Escort

2 Answers

Ford ka blows hot air even set at cold


sounds like heater control valve situated under scullle panel common fault on ka set heater fan switch half way between hot and cold with heater blowing then touch valve if pulsing or clicking noise it is faulty if doesnt solve problem faulty switch

Jun 07, 2009 | 1999 Ford Taurus

3 Answers

My heater is not blowing hot air, the air conditioner seems to be working, I replaced the heater and airconditioner switch module but it didn't help


I have a 2001 ford winstar and my heater is not working I slide the ac/heater switch to heat and all it does is let out a thumping sound and blow cold air out and it is starting to get cold in the morning

Jul 27, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
2007 Ford Bantam 1.3i Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...