Question about 1998 Mazda MPV

1 Answer

Water pump is good

Engine wont turn over water pump is good

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you're alternator is holding a full charge then check your starter.

Posted on Apr 21, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just changed the water pump on a 2005 dodge neon and now it wont start. What could it be


You're not giving much to go on. Is it a 2.0L or a 2.4L?
You say it won't start. Does it turn over and not fire, or does it just sit there and do nothing when you turn the key?

Both engines require you to remove the timing belt in order to change the water pump. The 2.0L is definitely an interference engine, and I'm not sure about the 2.4L. But if the timing belt was not re-installed properly, it will result in a no-start condition since the valves will not be in sync with the pistons and spark. Best case scenario you correct the issue and are good to go. Worst case scenario is that if the belt is out too far, you bent valves and have to service the head(s).

May 31, 2016 | 2005 Dodge Neon

1 Answer

1998 kia sportage 4WD engine turns but wont turn over (dosent even try) it just makes a winding sound and leaking coolant around harmonic balancer?


Sounds like your water pump leaking and a broken timing belt. The water pump runs off the timing belt, and sounds like your water pump took out the belt. The winding noise you hear sounds like the engine crank turning but not the cam shaft, broken belt, no compression. Have someone watch the harmonic while you try to start it. If it's turning, that's your problem.

Dec 18, 2013 | Cars & Trucks

1 Answer

Wont start but will turn over


Check wiring, you have accidently knocked something loose. the engine should run even without a water pump.

Nov 07, 2013 | 1993 Mercury Tracer

1 Answer

Water tank has frozzen


need to find a heat source to warm the vehicle(like a warm garage ) or some heater to set in the engine compartment to thaw the thing out..and by all means replace the water with antifreeze (almost full strength to refill the system,,this is provided all the freeze plugs arent pushed out or castings did not crack...with the ice in the system, the water pump is locked up and wont allow the engine to turn over..at this point I will bet that the engine is probably in need of replacement if my suspicions are correct...once thawed out I would be looking for antifreeze leaks anywhere ...I wish you good luck..

Jan 27, 2013 | Cars & Trucks

1 Answer

2003 sliverdo 5.3 engine, wont start, turn over,


check fuel preasure may have bad pump, try pouring i little gas down throtle body, if it fires up then i would say pump is bad, good luck.

Oct 07, 2009 | 2003 Chevrolet Silverado 2500HD

2 Answers

My 97 taurus is over heatin


sounds like cracked cylinder heads or blown headgasket

Aug 26, 2009 | 1999 Ford Taurus

1 Answer

I need directions to change my water pump


drain engine coolant.relieve belt tension .and remove the drive belt.remove upper fan shroud.remove fan or fan and clutch assembly.remove water pump pulley and coolant hoses from water pump.remove water pump bolts.then remove pump from engine.pay attention to bolts location because they are different lenghts.clean water pump gasket mounting surface dont scratch .or pump gasket wont seal and leak .apply sealant to water pump bolts.install water pump with new gasket.if gasket paper put a sealant on it.torque water pump bolts to 30 ft lbs.if you got a 2.2L engine torque water pump bolts to 18 ft lbs.install coolant hoses on pump .install water pump pulley.install fan and fan clutch assembly.install the drive belt .and the upper fan shroud.fill the radiator with coolant.then run engine to check for leaks.WARNING AS A SAFETY PRECAUTION REMOVE NEGATIVE BATTERY CABLE SO CAR WONT BE CRANK BY ACCIDENT. ALSOOOO DONT FORGET TO TURN OFF RADIO FIRST BEFORE DISCONNECTING BATTERY SO YOU WONT LOSE YOUR RADIO CODE.

Jun 01, 2009 | 1999 GMC Jimmy

1 Answer

New water pump wont start


It could be the crankshaft position sensor located near the crankshaft under you sparkling new water pump. Wires may be disconnected.:) Good Luck

Dec 10, 2008 | 1989 Dodge Raider

Not finding what you are looking for?
1998 Mazda MPV Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...