Question about Cars & Trucks

1 Answer

New batteries still low power - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

Try new battery cables

Posted on Apr 25, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My caddy dose not have any power after I tried to change the radio it was working fine until I tried to replace the radio


Try giving the vehicle a boost. Were the interior lights/ignition on during radio replacement? The battery may have run down. Even though a new battery, with accessories left on, it will drain causing the low voltage display

Jan 12, 2016 | 2002 Cadillac Deville

1 Answer

New battery and alternator but battery light stays on in 2006 cord escape


Firs make sure it is not the low coolant light and not the battery light, the low coolant light looks like a battery. If it is the battery light check the connector at the Alternator and see if there is power going to it, you can check with key on without car running.

Sep 02, 2015 | Cars & Trucks

1 Answer

Is it possible to have abs fault error due to low power battery ?


Not likely but could happen by replacing batter you probably cleared the code

Jan 09, 2015 | Cars & Trucks

2 Answers

Battery is good new alternator battery power still runs low


year make and model of the vehicle that wont charge the battery?

May 30, 2014 | 1991 Dodge Dakota

1 Answer

1994 Mazda Protege would not start battery seemed dead/low on power, replaced with a new battery car still would not start and has no power from the battery, no lights etc


sound like blowed fuse or fuse link near the battery or battery cables need replacing.check see if alternator getting 12 volts at the battery feed wire.

Sep 22, 2013 | Cars & Trucks

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

1994 jaguar xjs just clicks when i try to start it-battery is new. The starter bad?code was RR39


If there is a power drain - new battery or old - it needs to be well charged to start the car..
If the batt is charged well - it could be the starter solinoid or the starter..
However - the typical "clicking sound" is usually a low battery..
IF the batt is low - could be the charging sytem or a power drain ..

Jul 08, 2009 | 1998 Jaguar XJ8L

1 Answer

Engine turns over will not start, new battery, low power on dash


check battery terminals for corrosion, also try running a new ground wire to motor

Dec 24, 2008 | 2002 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...