Question about 2009 Dodge Caliber SXT

Open Question

2009 caliber fan not working hvac

Have new resister all fuses good

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: working on 2007 Dodge caliber XLT; mirrors (both)

I HAVE YHE SAME PROBLEM, YOU HAVE TO GO TO THE DODGE WORKSHOP , AND CONNECT THE MAIN COMPUTER SCANNER OF THEM, AND THEY RESTAR THE SYSTEM, IT WORKED FOR ME, WITH THAT COMPUTER ALL IS CONTROLLED, ENGINE AND TRANSMISSION, EVERYTHING ELECTRIC , AND THEY CAN CALIBRATE THE JETS GAS WITHOUT TOUCHING THE CAR ....
GOOD LUCK

Posted on Feb 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2007 Dodge Caliber radiator fans are not turning on and the fuse is okay what would be my next step


Check the relays under the hood. Either in fuse panel under hood or follow fan wires from fan and look for a relay on fenderwell or radiator support. If all is good try a jumper wire to fan motor and see if it comes on. If not fan motor may be bad. Most are replacable.

Jul 07, 2017 | Dodge Cars & Trucks

1 Answer

No heat or ac


Depending on the year , make , and model you have, most HVAC systems have a blower motor fan resister, usually located near the blower motor, check for power and ground at the fan resistor plug connector and make sure all connectors are in good shape, and not melted, or you will have to replace the fan resister pig tail as well.

Nov 29, 2015 | AC Cars & Trucks

2 Answers

Which fuse controls cruise control?ABS on a 2009 Dodge Caliber


Look at the underside of the main fuse box under the hood and the diagram should show you the size of each fuse and the relays as well as the function of each. Other fuse boxes will also have the same information, but I believe the main fuse box has the ABS and cruise in it.

May 29, 2015 | 2009 Dodge Caliber SRT-4

1 Answer

Which fuse controls cruise control on a 2009 Dodge Caliber


If there is a problem with the ABS the cruise control is disabled ! you have to fix the ABS problem for the CC to work !

May 29, 2015 | 2009 Dodge Caliber SRT-4

1 Answer

How do I unclog hvac plenum drains


compressed air and uncover the drain outside and use a wire clothes hanger to break the clog loose then use the compressed air on the inside to blow clog outside.

Oct 29, 2014 | 2009 Dodge Caliber

1 Answer

Driver vent has cold a/c passenger does not


You can start by trying an actuator recalication.(w/o scan tool)

1. clear all DTCs by disconnecting the battery.

2. remove the HVAC/ECAS fuse for a minmum of 10 seconds.

3. install the HVAC/ECAS fuse.

4. start the vehicle.

5. Wait 40 seconds for the HVAC control module to self-calibrate.
If this doesnot work, probably the right actuator is defective. You
will have to replace it. In the center of the HVAC module, there are two actuators, one is on the top part of the module and the other one is Under. The right actuator is the top one.

Jul 09, 2014 | 2009 Chevrolet Silverado 1500

1 Answer

My 2012 Dodge Caliber will only turn but will not start - the fuel pump is working, I replaced the starter; the battery does die when I crank a few times. I have also checked the fuel line working good....


the answer to your problem is in your explanation of " the battery dies when I crank a few times". Have a load test done on the battery for a failing cell. A failing battery will only supply enough power to crank but not enough power to run the ignition system. Power takes the path of least resistance and as a starter is a controlled dead short there is too much resistance in the ignition system so the car will not start.

Sep 06, 2013 | 2009 Dodge Caliber

1 Answer

No power to blower motor wiring on 2002 pont. grand prix. motor runs fine on bench and resister test good. Any ideas?


A bad ignition switch will cause this.

Check the i/p fuses first. there will be 4 you need to make sure are good. The DIC/HVAC, Radio, HVAC Cntrl, and HVAC hi. If the fuses are good check for power to the HVAC Cntrl fuse with the blower and resistor installed and plugged in, the ignition switch set to run, and the blower switch in any position. If there is no power to the fuse unplug the resistor and the blower and recheck. if there is power when those two are unplugged than the ignition switch is bad.

Nov 25, 2010 | 2002 Pontiac Grand Prix

1 Answer

Only have 1 speed on HVAC fan


the fan relay(resister) that control fan speed is probably burned out.When this occurs it will only blow at high speed because its getting 12volts directly to the fan

May 25, 2009 | 2004 Pontiac Vibe

Not finding what you are looking for?
2009 Dodge Caliber SXT Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...