Question about 2003 Dodge Intrepid

1 Answer

Cam sensor trying to locate the cam sensor on my 2003 Dodge Intrepid. it's a 3.5 V6

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

On front of the timing covers...

Posted on Apr 22, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

  • 19 Answers

SOURCE: 2005 dodge noen cam sensor

I own a 2002 neon sxt and recently had to replace the cam sensor it should be in the same place.
look on the right side of the motor you should see it. it'll have a small wire harness that clips in the top and its fastend with 4 bolts. Oh and take the battery out before you do it it makes it a lot easier.

Hope this helps.

Posted on Feb 25, 2009

  • 38 Answers

SOURCE: 2000 dodge intrepid 2.7 sputtering, revs up

you need to ck some basics you could have a vacuum leak which would hide during warm up but cause havoc when hot,the leak would cause high idle then your pcm would try to lower idle to spec thru use of idle control motor causing surging idle ,also fuel pressure needs to be checked while acting up,may be more cost effective to pay for an hour of diagnostic.

Posted on May 06, 2009

  • 137 Answers

SOURCE: 2003 stratus cam sensor replaced still unresolved

you bypassed the wires that connect to the sensors? that would have been my first guess the harness that plugs into the sensor. after that i would check the ground connection from the ecm. wouldn't hurt to check the battery posts too. if the battery posts are oxidized you can have all kinds of goofy electrical problems. hope that helps.

Posted on May 27, 2009

c17hydro
  • 2984 Answers

SOURCE: locate cam position sensor on 2004 dodge intrepid

The camshaft position sensor is mounted to the top of the timing case cover.

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I NEED TO KNOW THE LOCATION OF THE CAM SENSOR AND CRANK SENSOR ON MY 1999 DODGE INTREPID 2.7 LITER


Cam sensor is right in front under the planum and crank sensor is by the crank harmonic balancer pully. But why do you ask?

Mar 03, 2011 | Dodge Intrepid Cars & Trucks

1 Answer

Bad cam sensor, how do i feplace it...


On the 2.7L V6, it is on the front of the left cylinder head, just below the valve cover. One bolt holds it in position, and there is a single electrical connector. I'm not sure of the exact location on the 3.5L, but I would guess the same general area.

May 19, 2010 | 2002 Dodge Intrepid

1 Answer

How to change cam positiom sensor in 2000 dodge


The cam position sensor on the 2.7 engine is on the
driver side of your engine, right in the front of the head. there's a 10mm bolt. undo the bolt and pull it straight out. push the new one into the hole, and hold pressure on it until it's bolted back in.

If you have the 3.5, the cam position sensor is located on top of the timing cover. I just unbolt the upper intake just enough to lift it up a little. unbolt the cam sensor, pull it out and install the new one keeping pressure on it until it's bolted in.

I hope this helps

May 13, 2010 | 2000 Dodge Intrepid

1 Answer

Where is the camshft position sensor on a 03 dodge intrepid 2.7l Bank A


THE CAM SENSOR IS LOCATED IN LEFT(DRIVER'S SIDE) CYLINDER HEAD AT THE FRONT..1 BOLT AND A 3 WIRE CONNECTOR..REMOVE BOLT AND PULL SENSOR OUT TOWARD FRONT OF VEHICLE..YOU MAY HAVE TO WIGGLE SENSOR TO REMOVE..PICK UP A NEW ONE AND YOU WILL SEE WHAT IT LOOKS LIKE..PRETTY EASY TO REPLACE AND IS FAIRLY COMMON PROBLEM

Aug 29, 2009 | 2003 Dodge Intrepid

1 Answer

Where are the cam sensor and crank sensors located on my car?


Crank Sensor: Passenger side of transmission just to right and above the differential cover. Has 3 wires:

Light Blue/Dark Blue stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

If the car runs or cranks, you can test this sensor by first checking for power on RED wire with key ON. Should be 8-9.5 volts DC. Furthermore, connect a dwell meter to the signal wire by probing the back of the connector. Dwell reading should be 49-51%. If not, its likely bad.

If you remove the sensor, you MUST replace the paper spacer on the end of the sensor or you risk damaging the sensor or even the torque converter drive plate otherwise. Also make sure O-ring is in good shape and positioned properly.

Cam Sensor:
Facing Engine, it is on the driver side timing case housing, on top of the round part, just to the right of the fuel rail pipe where there is a capped fuel valve.

Has 3 wires:

Tan/Yellow stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

Testing is same as for Crank Sensor.

May 14, 2009 | 1994 Dodge Intrepid

1 Answer

No Start Replaced Cam Sensor Now Runs But Rough


I don't know if you have a coil pack or spark plug wires but this is what you need to check for the miss you can also try this website if needed for diagrams and instructions autozone.com or your local library

Mar 07, 2009 | 1998 Dodge Intrepid

1 Answer

Engine replacement


Yes, and update the software too on the computer... it happened to my mom...

Jun 18, 2008 | 2000 Dodge Intrepid

Not finding what you are looking for?
2003 Dodge Intrepid Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...