Question about 2000 Ford Expedition

1 Answer

Front turn signals don't work

Changed the multifunction arm and the signal relay, that fixed the problem with the rear signals but not the front....4 way flashers work fine

Posted by on

  • chretien1983 Apr 21, 2014

    sorry turns out the 4 way flashers don't work in the fron either and it's not a ford expedition it's an f350 super duty diesel

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 51 Answers

I'd look to see if your getting voltage if you are check your found to the front lights

Posted on May 19, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: 1999 ford expedition turn signals not working

It is behind center of instrument cluster just above the accel pedal in the blower/flasher relay block,it is actually a relay on this vehicle.

Posted on Feb 28, 2009

chuck943
  • 783 Answers

SOURCE: where is the flasher for the turn signals in a 1999 ford explorer

The 2 fuses are no 10 (7.5amp) and no 21(15amp) in the interior fuse panel.The flasher is located on the base of steering column under dash. See this this pic find connector c214 on bottom 3rd from right.
http://i253.photobucket.com/albums/hh43/chuck943/EXN15113.gif

Posted on Mar 14, 2009

  • 1 Answer

SOURCE: Turn signal problem

broken ground wire

Posted on May 08, 2009

  • 24 Answers

SOURCE: no turn signals but flashers work

You may have two relays one for hazards and one for turn indicators.

Posted on May 31, 2009

localwonder
  • 6784 Answers

SOURCE: turn signals and emergency flashers do not work

The turn signal flasher assembly is located under the driver's side of the instrument panel, on the front of the fuse panel, or under the center section of the instrument panel in the relay/flasher block. This is ,basically, the controller for your turn signals.

Click here to view a picture of the flasher switch.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My turn signals dont work i changed the relay and it still wont work..


it is most likely not the relay but the flasher that is bad

Feb 23, 2013 | 1994 Dodge Intrepid

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

1999 ford f 550 turn signal and hazard lights are not working. fuses are good.


I am not familiar with this vehicle, but I am confortable with wiring diagrams. I pulled the electrical diagram for the model year 1999 HD/350/SUPER DUTY (which would include your F-550). I would suspect the hazard switch in your multifunction switch/arm/wiper lever. It is the only common thing between the 2 systems, and both are wired through 2 different flasher assemblies through 2 separate wires to the multifunction switch/arm. In fact, the hazard lights are a hot battery item and bypass the turn signal switch for the front turn signals as well as the indicators in your dash.

Try to check if your stop lights do come on when you hit the brakes... if they don't, your problem is really with the hazard switch within the multifunction switch/arm.

I do not know if this switch can be replaced separately from the multifunction switch/arm, but from what I found surfing the net, the whole thing (multifunction switch/wiper lever) goes for about 50$. There are some DIY on the internet to replace the assembly, but it would seem it can be a bit tricky to replace for someone not familiar around the steering wheel portion.

Hope this helps.

Sep 14, 2011 | Ford F-450 Cars & Trucks

1 Answer

I have a 2003 2 door explorer sport, just recently my turning signal and break light have stopped working on the passenger side!! I changed the light bulb, and nothing!! I changed the turning signal light...


No, because the left side is still working. The loose wiring was to the multifunction switch (turn signal).

Power gores through the turn signal switch to the brake switch on the brake pedal, then to the rear lights. Does the highmount brake lamp work?
At the RH lamp socket, Measure the voltage between the RH rear lamp C4032 pin 3, circuit 5 (OG/LB), harness side and ground. Should be 12 volts.

try that first.

Did you change the front and rear bulbs?

May 21, 2011 | Ford Explorer Sport Cars & Trucks

1 Answer

How to change multifunction switch on 04 buick century


STEP BY STEP INSTRUCTION First, any time you work around the steeringcolumn you it is a must to disable the air bag system you will do this my disconnectingthe battery. After you disconnect the battery wait at least 5 minutes before proceeding. 1. Ifyou have tilt remove the tilt actuator arm by firmly pulling straight out. 2. Removethe upper and lower trim covers. 3. Removethe wire harness assembly from the wire harness strap. 4. Disconnect the turn signal andmultifunction switch assembly connector from the SIR system coil connector.This is alongside the steering column there is an 8mm bolt in the center of theconnector that must be removed to disconnect the connector halves. 5. Slide the 2 connectors of the turnsignal and multifunction switch assembly out of the bulkhead connector. With a smallscrewdriver slightly pry between the connectors to release them. 6. Removethe 2 pan head tapping screws and from the turn signal and multifunction switchassembly. 7. Removethe turn signal and multifunction switch assembly from the steering column tilthead assembly. INSTALLATION PROCEDURE 1. Installthe turn signal and multifunction switch assembly onto the steering column tilthead assembly. 2. Screwthe 2 pan head tapping screws and into the turn signal and multifunctionassembly.3. Slidethe 2 connectors of the turn signal and multifunction switch assembly into thebulkhead connector. 4. Connectthe turn signal and multifunction switch assembly connector to the SIR coilconnector. 5. Installthe wire harness assembly (1) into the wire harness strap (2). 6. Installthe upper and lower trim covers. 7. Installtilt actuator arm. 8. Reconnectthe battery.


Mar 01, 2011 | Buick Century Cars & Trucks

1 Answer

Left turn signal comes on and flashes but not the right one


If the arrow stays on on the dash, you have a burnt bulb on the right side. If the front right bulb stays on and the right rear is out, the rear bulb is burnt. If the rear is on solid, the front is burnt. If both front and rear is on, either you have a bad connection at the sockets, bad turn signal relay, or a bad multifunction switch - which is usually the turn signal switch in the steering column.

Dec 19, 2010 | 1996 Ford Windstar

3 Answers

If my blinkers are not working anymore, what can it be?. I checked the fuses and they are good


try your turn signal relay. i'm not sure where it is in a firebird though. check around the fuse box and around the computer

Feb 28, 2010 | 2000 Pontiac Firebird

1 Answer

Rear turn signals work, not the front


most likely the multifunction switch is defective.

Sep 10, 2009 | Dodge Colt Cars & Trucks

3 Answers

1999 ford expedition turn signals not working


It is behind center of instrument cluster just above the accel pedal in the blower/flasher relay block,it is actually a relay on this vehicle.

Feb 28, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...