Question about 2005 Chrysler Pacifica

1 Answer

Head torque bolt specs for 2005, 3.5L pacifica. I mean screw cap top block.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 813 Answers

Replace bolts and torque to 65 foot pounds and this is the 3rd torque work up to it then turn the bolt to 90 degrees the torque should show 90 foot pounds or better

Posted on May 18, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 599 Answers

SOURCE: torque specs on replacing cv axle on 05 Pacifica

ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Posted on Jan 07, 2010

Testimonial: "thank you very much!!!!!!!!!!"

chargerhp
  • 813 Answers

SOURCE: i am replacing the intake gasket on my 2005

If you are looking at the engine from the front and the large hose is at the bottom right the tightening sequence is from upper left to right 6237 bottom left to right 5148 just like I typed it torque is 250 inch pounds on lower intake and 105 inch pounds on the upper intake. So when you look at those numbers you tighten 12345678 in that order to 250 inch pounds in 3 increments then install the top intake.

Posted on Feb 25, 2010

thunderz
  • 232 Answers

SOURCE: need torque specs for head bolts for 2004 PT

For specs like that I would call the parts counter at your local Chrsler Deal and they will be acurate and glade to help you.

Posted on Mar 11, 2011

  • 43 Answers

SOURCE: i need the head bolt

CYLINDER HEAD BOLT TORQUE
Use a torque wrench to tighten the bolts to 76 - 83 ft. lbsof torque in the order shownTightening should be done in two or three steps.

CAUTION: Install the head bolt washers with shear dblackjakjunk.gifroop upward as shown in the illustration

Posted on Jun 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

Cylinder head to engine block torque sequence and ft lbs


    images for Cylinder head to engine block torque and ...
    More images for Cylinder head to engine block torque and sequence

    Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

    boxwrench.net/specs/chevy_sb.htm
    their specs. Click Here! 3/8 Connecting Rod Bolt, Engine Oil, 45 ft-lbs. 11/32 Connecting Rod Bolt, Engine Oil, 35 ft-lbs. Cylinder Heads. Engine oil. (blind hole).

    [PDF]

Nov 29, 2015 | Cars & Trucks

1 Answer

Torque specs for upper intake manifold for an '07 Chrysler Pacifica 4.0


10mm nuts (6mm bolts) in aluminium usually require less than 7 ft/lbs (10Nm) of torque as its just a box bolted to a vacuum source. if you cant find torque specs, use internet charts for bolt sizes on something like this. Does not apply to head bolts as they are special

Aug 18, 2015 | Chrysler Cars & Trucks

1 Answer

On a 3.8L what is the aspec diagram and tourque for the racker arm


Hi Juan, I'm AL the owner of Big As Auto Repair

Below is the torque specs for the rocker arm as you requested.

SPECIFICATIONS - TORQUE

DESCRIPTION N·m Ft. Lbs. In. Lbs. Camshaft Sprocket-Bolt 54 40 - Camshaft Thrust Plate-Bolts 12 - 105 Forged Connecting Rod Cap-Nuts 54 +¼ turn 40 +¼ turn - Cracked Connecting Rod Cap-Bolts (Refer to 9 - ENGINE/ENGINE BLOCK/PISTON & CONNECTING ROD - INSTALLATION) Crankshaft Main Bearing Cap-Bolts 41 +¼ turn 30 +¼ turn - Crankshaft Main Bearing Cap Cross Bolts (3.8L) 61 45 - Crankshaft Oil Seal Retainer Rear-Bolts 12 - 105 Crankshaft Damper-Bolt 54 40 - Cylinder Block Drain Plugs 20 15 - Cylinder Head-Bolts (Refer to 9 - ENGINE/CYLINDER HEAD - INSTALLATION) Cylinder Head Cover-Bolts 12 - 105 Flex Plate to Crankshaft 88 65 - Engine Mounting (Refer to 9 - ENGINE/ENGINE MOUNTING) Powertrain Torque Strut 54 40 - Exhaust Manifold-Bolts 23 - 200 Exhaust Crossover Pipe-Bolts 54 40 - Intake Manifold - Lower-Bolts 23 - 200 Intake Manifold - Lower Gasket Retainer-Bolts 12 - 105 Intake Manifold Upper-Bolts 12 - 105 Lifter Yoke Retainer-Bolts 12 - 105 Oil Filter Attaching Fitting 54 40 - Oil Cooler Attaching Fitting 27 20 - Oil Filter 20 15 - Oil Filter Adapter-Bolts 28 - 250 Oil Gallery Plug 27 20 - Oil Pan-Bolts 12 - 105 Oil Pan Drain-Plug 27 20 - Oil Pressure Switch 23 - 200 Oil Pump Cover Plate-Screws 12 - 105 Oil Pump Pick-up Tube-Bolt 28 - 250 Oil Dipstick Housing-Bolts 48 35 - Rocker Arm Shaft-Bolts 23 - 200 Spark Plug 16 12 - Thermostat Housing 12 - 105 Timing Chain Case Cover -M8 Bolt 27 20 - -M10 Bolt 54 40 - Water Pump-Bolts 12 - 105 Water Pump Pulley-Bolts 28 - 250
Should you need extra help visit my website here: http://www.bigasautorepair.com/

Apr 15, 2015 | 2005 Chrysler Pacifica

2 Answers

What the torque specs. For a 2002chevys10 4.3vortex mains and rod bearing


Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

Mar 25, 2015 | 2002 Chevrolet S-10

1 Answer

Torque specs for 3.2 1995 heads on my isuzu... I need to fix the car ASAP....


Hi, to install follow the procedure below:


  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

Best of luck............

May 30, 2011 | 1995 Isuzu Trooper

1 Answer

Torque specs for 3.2 1995 heads on isuzu rodeo heads


0900c152800622a3.gif

To install:

  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

May 16, 2011 | 1995 Isuzu Rodeo

2 Answers

Need torque specs for 83 chevy 350 cylinder head bolts.


Hello there
Torque Specs
These specs may not be correct for your application.
Verify your engine specs with a service manual for your year and model.
always torque bolts in three equal increments
Bolts or Parts Lube or Sealer Torque to: 7/16 Main Caps (2 bolt) Engine Oil 70 ft-lbs. 7/16 Inner Main Caps (4 bolt) Engine Oil 70 ft-lbs. 7/16 Outer Main Caps (4 bolt) Engine Oil 65 ft-lbs. 3/8 Outer Main Caps (4 bolt) Engine Oil 40 ft-lbs. Warning!!! If you are using ARP bolts, you MUST use
their specs. Click Here! 3/8 Connecting Rod Bolt Engine Oil 45 ft-lbs. 11/32 Connecting Rod Bolt Engine Oil 45 ft-lbs. Cylinder Heads
Engine oil
(blind hole)
Sealer
(water jacket)
65 ft-lbs.
Rocker Studs (screw-in) Engine Oil 50 ft-lbs. Oil Pump Engine Oil 65 ft-lbs. Oil Pan Engine Oil 12 ft-lbs. Cam Sprocket (upper gear) Thread Locker 20 ft-lbs. Timing Cover Engine Oil 6 ft-lbs. Intake Manifold
(Cast Iron Heads)
Non- Hardening Sealer 30 ft-lbs. Valve Cover Engine Oil 3 ft-lbs. Exhaust Manifold Anti-Seize Lubricant 25 ft-lbs. Spark Plugs No Lube or Sealer 20 ft-lbs. Flexplate (Automatic)
Flywheel (Clutch)
Thread Locker 60 ft-lbs. Clutch Pressure Plate Thread Locker 35 ft-lbs. Centerbolt
(Harmonic Damper)
Engine Oil 60 ft-lbs. Bellhousing
(Transmission to Block)
Engine Oil 25 ft-lbs. Head Bolt Tightening Sequence
sbchvy_head_seq.gif

Apr 16, 2010 | 1983 Chevrolet Chevy

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...