Question about 1995 Chevrolet Blazer

1 Answer

95 chevy blazer won't accelerate, has rough idle and back fires

95 Chevy blazer s10 will not accelerate, it also has a rough idle and it putters and back fires

Posted by on

  • Stephyy Quesada
    Stephyy Quesada Apr 21, 2014

    we've already changed the o2 sensor the maps sensor and the egr vavle and it hasnt improved

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

When was the last tune up done on it? have you checked the spark plugs and firing order to make sure it is correct?

Posted on Apr 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

c17hydro
  • 2984 Answers

SOURCE: firing order for v6 chevy distributor

Counter-clockwise on the distributor in the figure...it is 1-2-3-4-5-6....#5 is the blue one and #6 is the purple one then #1 and so on....

f336f66.gif

Posted on Apr 03, 2009

  • 77 Answers

SOURCE: firing order for 97 chevy blazer

Firing order is 1-6-5-4-3-2. Distributor cap should be numbered. Number one cylinder is front on driver's side (3 and 5 follow on same side). Number 2 is front on passenger's side (followed by 4 and 6).

Posted on Apr 29, 2009

  • 66 Answers

SOURCE: firing order for 4.3 liter chevy blazer

1-6-5-4-3-2

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Chevy Blazer S10.. Won't start.. It was


sound you have a blown clutch slave cylinder

Dec 05, 2012 | Cars & Trucks

1 Answer

Have a 95 chevy blazer idles rough after warms up. gives black smoke


Sounds like you have a fuel leak inside the intake. Remove the upper intake manifold. Cycle the key on and off and check for leaks from the fuel lines and pressure regulator.

Jun 09, 2010 | 1995 Chevrolet Blazer

1 Answer

Need firing order diagram for 91 s10 blazer


991 Chevy S10 firing order
The firing order for a Chevy s10 depends on which engine you have.
1.9L engine the firing order is: 1-3-4-2 . Distributor rotates counterclockwise.
2.0L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.5L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.8L engine the firing order is: 1-2-3-4-5-6 . Distributor rotates clockwise.
4.3L engine the firing order is: 1-6-5-4-3-2 . Distributor rotates clockwise.

Jan 09, 2010 | 1991 Chevrolet S-10

1 Answer

My 1992 chevy s-10 blazer, starts, but dies out when in gear.


Sounds like it could be a mis-fire. At an idle, remove a plug wire to see if it stalls. If it does, re-install it and go to the next one. If you remove one and get no change, that cylinder is the problem. Test for spark.

Oct 06, 2009 | 1992 Chevrolet S-10

1 Answer

I have a 94 chevy s10 blazer that skips when accelerating and idl


low compression - worn spark plugs and wires - weak coils-clogged fuel filter.

Apr 27, 2009 | 1994 Chevrolet S-10 Blazer

2 Answers

Blazer runs awful....


i had the same issue after having replaced the egr sensor and the O2 sensors turns out the fuel pump was bad.

Dec 30, 2008 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...