Question about Chevrolet Silverado 2500HD

1 Answer

Knock sensor replacement

Where is the knock sensor located

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

Depending on the year, you can one or two of them. Newer models have two. One on each side of the block, located about in the center of the block. Older ones stick out a bit and are about the size of a silver dollar. Newer ones have a bolt that goes thru the center of them with some wires attached. Be careful, the older ones mount into a water jacket. Antifreeze will come out.

Posted on Jun 13, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 366 Answers

SOURCE: knock sensor replacing

under intake manifold bracket!

Posted on Mar 15, 2009

  • 102 Answers

SOURCE: 1986 jetta oil pump location and replacement/knock sensor

oil pump is in the oil pan and if you have no or low oil pressure replace pump before doing anything with knock sensor. knock sensor is more or less a microphone and listens for spark knock but will set codes for any knocking or tapping noise which is commonly heard if oil pump is malfunctioning

Posted on Mar 22, 2009

  • 422 Answers

SOURCE: 2001 hyundai elantra knock sensor

yes sir, the knock sensor is located on the side of the engine block, the side closest to the firewall. it is just a small circular object with a wire connector and one bolt

Posted on Aug 27, 2008

emissionwiz
  • 76848 Answers

SOURCE: need to replace knock sensor/ O2 sensor 04 kia rio

IT IS IN THE SIDE OF THE ENGINE BLOCK, SCREWED INTO THE WATER JACKET OF THE BLOCK

Posted on Sep 18, 2009

  • 176 Answers

SOURCE: need to know where knock sensor is located on a 2001 kia rio.

At center rear of engine compartment, by intake manifold support bracket.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 nissan sentra sx 200 knock sensor location


Melvia, Knock sensor located under the intake manifold between cylinder #2-3 I believe, hard to change with out removing intake manifold, but can be done. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
1995 1999 Nissan Maxima 1 2 Knock sensor replacement
KA24DE Knock Sensor Code 34 FREE REPLACEMENT How To
Knock sensor on 1995 Altima
Get the Best Priced Nissan Sentra Knock Sensor

Aug 21, 2016 | Nissan Cars & Trucks

1 Answer

04 Chevy avalanche knock sensors location


Nathan, 2 Knock's are located under intake manifold.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Engine Knock Sensor 2000 06 5 3L Silverado Sierra...

Knock sensor 5 3 4 8 6 0 replacement

05 Chevy Avalanche Knock Sensors

4 8 5 3 6 0 knock sensor replacement GM



Mar 06, 2016 | Cars & Trucks

1 Answer

2004 3.0L Escape. Where are the knock sensors located?


Knock Sensor

Print
Operation

The Knock Sensor (KS) is a tuned accelerometer on the engine which converts engine vibration to an electrical signal. The PCM uses this signal to determine the presence of engine knock and to retard spark timing.
Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the intake manifold.
  3. Remove the bolt and the Knock Sensor (KS).
  4. To install, reverse the removal procedure and tighten mounting bolt to 15ft. lbs. (20 Nm).

Jul 21, 2015 | Ford Cars & Trucks

1 Answer

2005 suburban 5.3 engine where are knock sensors located and how do you replace them


two knock sensors.under phlemm assy. replace cover gasket, two sensors and wire harness.

Jan 27, 2013 | 2005 Chevrolet Suburban

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

4 Answers

Where is knock sensor located on 2001 silverado 6000 engine


Under the intake manifold. Make sure you get the harness for the knock sensors. and clean out all of the rust and junk you're going to find donw in the holes before and after you replace the sensors.

Nov 01, 2009 | 2005 Chevrolet Silverado

4 Answers

Need to locate knock sensor on 1999 camry V6. Where is located.


i have toyota windom 4vz-fe i need locate knock sensor

May 31, 2009 | 1999 Toyota Camry

2 Answers

Location of knock senor on 97 maxima se


Your knock sensor is located Under the hood, center, front engine area, below intake manifold, mounted on block.


A defective knock sensor may cause engine detonation or reduced spark advance and fuel economy. When a knock sensor is removed and replaced, the sensor must be tightened to its specified torque. If the knock sensor is installed tighter than it should be, it may become too sensitive and provide an excessively high voltage signal, resulting in more spark ****** than required. When the knock sensor is installed looser than it should be, the knock sensor signal will be lower than normal, resulting in engine detonation.

To replace the knock sensor:
  • Disconnect the knock sensor wiring connector.
  • Then, unscrew the sensor.
  • Remove the knock sensor.
  • Reverse the procedures to install the part.

May 15, 2009 | 1997 Nissan Maxima

1 Answer

1986 jetta oil pump location and replacement/knock sensor


oil pump is in the oil pan and if you have no or low oil pressure replace pump before doing anything with knock sensor. knock sensor is more or less a microphone and listens for spark knock but will set codes for any knocking or tapping noise which is commonly heard if oil pump is malfunctioning

Mar 20, 2009 | 1986 Volkswagen Jetta

1 Answer

Knock sensor location


Knock Sensor Description addthis_pub = 'car-suff'; button1-bm.gif parts-box-top-lft.gif parts-box-top-rt.gif knock-sensor.jpg parts-box-rt.gif parts-box-btm-lft.gif parts-box-btm-rt.gif A quality Knock Sensor is more important than ever thanks to today’s increasing gas prices. Your Engine Knock Sensor enables your vehicle to obtain the optimum combination of timing and fuel/air mixture to generate power and efficiency and that means less wasted gas. Our guaranteed low prices make us your one-stop Knock Sensor Location. Regardless of the brand, make or model car, truck, van or SUV you drive, we make it easy to locate the application specific Knock Sensor that’s perfect for your vehicle. Our state of the art parts locating system puts you just a few mouse clicks away from the Knock Sensor you need and at a price you cannot beat anywhere. Click. Click. Click. And you are there. In addition to robbing you of fuel economy and performance a faulty Knock Sensor can cause expensive damage to your engine. Remember, the Knock Sensor keeps fuel from detonating in the cylinder … exploding rather than quickly burning as it should. If not replaced a faulty Knock Sensor can quite literally cause hundreds if not thousands of dollars in damage. There is really no need to look any further to find the Knock Sensor that’s application specific for your car, truck, van or SUV – high performance or family vehicle. We’ve got guaranteed low prices and shipping that other suppliers envy. Give us a try, we think you’ll be happy … in fact we guarantee it.

Jun 20, 2008 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...