Question about 2004 Renault Megane

1 Answer

Problem with fuel indicator - 2004 Renault Megane

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Hi, you don't give any detail to the exact problem, but if you remove the connection wire from the fuel tank, the with the ignition on - put the wire to earth. if the fuel gauge rises to full on the dash it means the transmitter in the tank is knackered. if the fuel gauge doesn't rise then its the gauge in the dash, hope this helps.

Posted on May 25, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Ford Focus and the fuel light stays on. It is very dim, even when I shut the car off.


Principles of Operation
NOTE: When installing a new instrument cluster, the new instrument cluster must be configured. Refer to Section 418-01 .
The instrument cluster is a hybrid electronic cluster (HEC) which receives and outputs information using both hardwired circuitry and the controller area network (CAN) communication circuits.
It is very important to understand:
  • where the input originates from.
  • all the information necessary for a feature to operate.
  • which module(s) receive(s) the input or command message.
  • if the module that received the input controls the output of the feature, or if it sends a message over the CAN to another module.
  • which module controls the output of the feature.
The instrument cluster carries out a prove-out when the ignition switch is turned from the OFF to the RUN position to verify the integrity of the warning indicators. The charging system warning indicator, the low oil pressure warning indicator and the malfunction indicator lamp (MIL) illuminate when the key is turned to the ON position, and then turn off when the engine is started. The seat belt warning indicator proves-out for 60 seconds and then turns off, or turns off when the seat belt is fastened. The following indicators prove-out when the key is turned to the ON position:
  • door ajar warning indicator (3 seconds)
  • anti-lock brake system (ABS) warning indicator (3 seconds)
  • O/D OFF indicator (3 seconds)
  • air bag warning indicator (6 seconds)
  • brake warning indicator (3 seconds)
  • door ajar warning indicator (3 seconds)
  • shift up indicator (3 seconds)
  • low fuel warning indicator (3 seconds)
  • traction control indicator (3 seconds)
  • check fuel cap indicator (3 seconds)
  • passive anti-theft system (PATS) indicator (3 seconds)
Low Fuel Warning Indicator
The instrument cluster utilizes fuel level data supplied by the hardwired fuel pump module to control the low fuel warning indicator, which illuminates when the fuel drops to a pre-determined level.
Your best bet is to take this to the Ford dealer , unless you have Ford IDS - factory scan tool to diagnose this
Your best bet

Dec 29, 2015 | Ford Cars & Trucks

1 Answer

What does the fuel reset indicator stands for? Ford explorer 98


Hey Carlos , does your vehicle run ?
Fuel Reset
The FUEL RESET indicator is grounded through the inertia switch whenever the vehicle is subjected to a high force situation. The inertia fuel shutoff switch (IFS switch) (9341) cuts off the fuel pump motor. The FUEL RESET indicator illuminates when the IFS switch has been tripped.

Mar 31, 2015 | 1998 Ford Explorer

2 Answers

What does the fuel reset indicator on the panel stands for? Ford explorer 98


Fuel Reset
The FUEL RESET indicator is grounded through the inertia switch whenever the vehicle is subjected to a high force situation. The inertia fuel shutoff switch (IFS switch) (9341) cuts off the fuel pump motor. The FUEL RESET indicator illuminates when the IFS switch has been tripped

Mar 31, 2015 | 1998 Ford Explorer

1 Answer

I have caprice 93 equipped with an analog dash board, the fuel meter is all the time indicates Full and never change its indication


Look at the wires to the fuel sender (wires on the fuel tank) It sounds like the main one is touching the tank or the car body.

Dec 21, 2013 | Cars & Trucks

1 Answer

2007 Hyundai Entourage codes P2187, PP0174,P2189,P2195,P2270,P2272


I've come across these codes before. In almost every case there was an air leak in the intake air hose (hose between the engine air filter & the throttle body). Inspect this hose & tubes attached to it. This is especially true when the lean code includes the comment 'at idle'
P2187 - System too lean at idle Bank 1
P0174 - System too lean Bank 2
P2189 - System too lean at idle Bank 2
P2195 = HO2S Signal Biased/Stuck Lean (Bank 1 Sensor 1)
P2270 = HO2S Signal Stuck Lean (Bank 1 Sensor 2)
P2272 = HO2S Signal Stuck Lean (Bank 2 Sensor 2)

P2187 & P2189 = In order to provide the best possible combination of drivability, fuel economy and emission control, the PCM uses a closed loop air/fuel metering system. The PCM monitors the HO2S signal voltage and adjusts fuel delivery based in closed loop fuel control. Changes in fuel delivery will be indicated by the long-term and the short-term fuel trim values. The ideal fuel trim value is around 0%. The PCM will add fuel when the HO2S signal is indicating a lean condition. Additional fuel is indicated by fuel trim values that are above 0%. The PCM will reduce fuel when the HO2S signal is indicating a rich condition. Reduction in fuel is indicated by fuel trim values that are below 0%. The DTC relevant to fuel trim will be set when the amount reaches excessive levels because of a lean or rich condition

Aug 31, 2011 | 2008 Hyundai Entourage

1 Answer

Malfunctionning gas indicator was low on


Its a fualty sending unit. Unfortunately its part of the fuel pump which is in the fuel tank. The only way to fix it is to replace the fuel pump assembly.

Mar 11, 2011 | 2008 Chevrolet Impala

1 Answer

On a 2001 ford taurus what is the exclamatin point on the dash? The light comes on and goes off at times.


Hope this helps.
df697aa.gif


Item Part Number Description 1 — Instrument cluster 2 — Odometer reset shaft 3 — Air bag warning indicator 4 — RH turn signal indicator 5 — Charging system warning indicator 6 — Tachometer 7 — Low oil pressure warning indicator 8 — Brake system warning indicator 9 — Cruise control indicator 10 — Check fuel cap indicator 11 — Anti-lock brake system (ABS) warning indicator 12 — Check transmission indicator 13 — Odometer 14 — Transmission range selector indicator 15 — Trip odometer 16 — Theft indicator 17 — Low coolant indicator (if equipped) 18 — Safety belt warning indicator 19 — Low fuel warning indicator 20 — Fuel gauge 21 — Malfunction indicator lamp (MIL) 22 — Door ajar warning indicator 23 — Traction control indicator (if equipped) 24 — Engine coolant temperature gauge 25 — High beam indicator 26 — LH turn signal indicator 27 — Speedometer

Jun 05, 2010 | 2001 Ford Taurus

1 Answer

Fuel indicator


OK, your fuel indicator is wired to a sending unit that is located inside the fuel tank. this assembly is part of the fuel pump assembly. the fuel indicator sending unit is housed in the same assembly as the fuel pump. The fuel indicator will not function properly if there is a bad ground or, if there is a fault within the sending unit. there is a floater device attached on this assembly and, it raises with the fuel level and lowers when the fuel level is low, sending resistance signals to the indicator gauge on your dash board. these signals can be disrupted if the ground is corroded or, if the sending unit is damaged. In most cases, replacing the sending unit will fix this issue. if the fuel indicator is stuck on the full mark, check the ground. if the fuel gauge is laying on empty all the time, replace the sending unit.

Jun 10, 2009 | 1996 Toyota Camry

1 Answer

Fuel level low symbols still shows


It's either a faulty tank sensor or a faulty fuel indicator light. Get the fuel indicator light checked first.

Oct 17, 2008 | 2001 Audi A4

Not finding what you are looking for?
2004 Renault Megane Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4861 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...