Question about 2001 Dodge Durango

1 Answer

Po441 how to fix and locate integrity monitor

Posted by on

  • Larry Williams Apr 23, 2014

    should be 2010 dodge journey

×

1 Answer

Type the code into Google

That is how you find the codes,problems &
part of the solutions

OBD PO441

Posted on Apr 23, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble codes po441


po441 is a netural vapor pressure switch or better knowen as evap purge flow monitor . whats happing is you building to much pressure in fuel tan, with car jacked up in the rear look for a charcoal canister,a plastic box that looks like it has 2 chambers .with hoses going to fuel tank and a 2 wire plug see if its disconnected or hoses are cracked ,broken ,or leaking. good luck ,I really hope I answered your question .
Woody

Aug 11, 2014 | Jeep Liberty Cars & Trucks

1 Answer

How to locate 2010 dodge journey evap. system to fix po441 code


Code P0441 is for evaporative purge performance and may be a false code which can be corrected by a newer computer flash update. This would be a free service at the dealer due to a -Rapid Response Transmittal- so call a dealer and have them run your VIN number to see if may apply due to build date of vehicle.

Apr 21, 2014 | 2010 Dodge Journey

1 Answer

Which solonoid do I fix on a 2000 Impala Evap System (code P0441) The vent solonoid or purge solonoid?


you see code po441 the purge solenoid could be faulty or disconnected. if you have problem with evap switch to vent solenoid you would smell gas fumes in vechicle.check make sure gas cap on tight not leaking because it will set off code po441.

Feb 07, 2012 | 2000 Chevrolet Impala

1 Answer

I DONT KNOW WHERE MY EVAP PURGE SYSTEM IS LOCATED AT ON MY 2004 DODGE INTREPID I NEVER SEEN ONE B4, BUT I TOOK THE EMISSIONS TEST AND A CODE CAME BACK PO441 IT CAUSED ME TO FAIL THE TEST I NEED TO GET THIS...


Yep the P0441 is : The evaporative emission control bad purge flow. You wont be able to run the component test for this issue without a good scan-tool of component tester. It may have to do with the flow control valve. It should be located next to the charcoal canister.

May 03, 2010 | 2004 Dodge Intrepid

1 Answer

PO441 engine code


this means your evap purge flow monitor is malfunctioning insufficient or excessive vapor flow detected during evaporative emission system operation it has to do with your fuel vapours

Jan 22, 2010 | 2004 Dodge Grand Caravan

1 Answer

1998 A-6 quattro 2.8L V6 (AHA) I have two codes coming up PO432; states, main catalyst efficiency below threshold (bank2) PO441; states, Evaporation Emission system incorrect purge flow. The car runs...


PO432= 1 OF THE SENSOR IN THE EXHAUST SYSTEM if u stand in front of engine to your rt under the car should be a oxygen sensor just unplug it and put a new one.....(bank2)
PO441 = Evaporative Purge Flow Monitor check your fuel cap and replace all of your vacuum hoses because they can be damaged or plugged this should fix it.
So good luck to ya....

Oct 14, 2009 | 1998 Audi A6

2 Answers

Check engine light on po441


P0441 = Evap. Emission Ctrl. System Incorrect Purge Flow. Listed Cause - valve stuck in open position.
INSPECTION (4 cylinder engine)
When disconnecting the vacuum hose, make an identification mark on it so that it can be reconnected to its original position.cc59427.jpg 1. Disconnect the vacuum hose (black with red stripe) from the solenoid valve. 2. Detach the harness connector. 3. Connect a vacuum pump to the nipple to which the red-striped vacuum hose was connected. 4. Apply vacuum and check when voltage is applied to the EVAP Canister Purge Solenoid Valve and when the voltage is discontinued.
31f3588.jpg Battery voltage Normal condition
When applied Vacuum is released
When discontinued Vacuum is maintained

V6 Purge Solenoid Valve
bc8d2fa.jpg

Jun 04, 2009 | Hyundai Motor 2002 Sonata

2 Answers

1997 toyota camry check engine light on codes are po441,po446


p0446 is an evap code for incorrect purge flow, check the rear vacume switching valve. its above the rear sub frame

Apr 05, 2009 | 1997 Toyota Camry

2 Answers

2003 toyota highlander OBD code's po442/po446/po441


if the air filter was recently inspected or changed, look for the vacuum hose to be disconnected from the valve located on the air filter cover. another source may be the gas cap either loose or with the tether strap caught under it preventing a proper seal

Dec 20, 2008 | 2003 Toyota Highlander

Not finding what you are looking for?
2001 Dodge Durango Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...