Question about 1997 Acura CL

Open Question

Drivers side window on 1997 acura 2.2cl won't work.

How do I troubleshoot window problems on the 1997 Acura 2.2cl

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: acura tl won't start

Ignition switch problem?

Posted on Jul 07, 2008

keemo68
  • 1263 Answers

SOURCE: blower motor for a 1997 acura tl

one of 2 places either under the dash behind the glove box or under the hood on the passengerside. first i would check the fuse and or fan motor relay. these are located in the box under the hood or under the dash on the drivers side. also i would check the reostat which controls the fan speed this is located near the motor and is held in place by 2 screws and has 2 wires hooked to it. one more thing to check is to make sure the switch is still good

Posted on Aug 29, 2008

tony chavous
  • 50 Answers

SOURCE: Find oil filter in engine of acura CL

back side of block under intake if its a 2.2 or a 2.3 if its a 3.0 its on the passenger side of engine bay if you turn the wheel you will be looking at it

Posted on Feb 03, 2009

  • 1 Answer

SOURCE: have 1997 Acura CL.. need radio code. Acura

Remove the ash tray and the code is on the back of the ash tray.

Posted on Oct 04, 2009

c17hydro
  • 2984 Answers

SOURCE: how to locate the thermostat for a 1997 acura 2.2

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Locate the thermostat housing by following the upper radiator hose to the engine.
  4. Loosen the hose clamps then carefully detach the hose from the fitting.
If the hose is stuck, carefully use a pick to break the seal between the radiator hose and the housing. If the hose is deteriorated, replace it with a new one.
  1. Disconnect any sensors or switches that may interfere with the removal of the thermostat from the housing.
f163710.gif
Remove the thermostat housing bolts

120abfd.gif
Pull the water outlet neck away from the housing

d9be9b2.gif
Note the installed position of the thermostat, then remove it

  1. Unfasten the retainers, then remove the thermostat housing.
Some coolant may leak out of the housing as the seal is broken.
  1. Remove the thermostat carefully noting how it's installed.
  2. Clean the mating surfaces of the thermostat housing.
Many thermostat housing's are made out of aluminum alloy. A plastic scraper is very effective and will not harm such metals.
To install

1c8dd82.gif

A new gasket must be installed before installation

c732e7b.gif
Install the thermostat with the air bleed valve at the top

  1. Install the new thermostat and gasket.
Install the thermostat with the jiggle pin facing up. This acts as an air bleed and must be at the top of the thermostat to operate properly.
  1. Install the thermostat housing, then tighten the bolts securely.
  2. Connect the radiator hose and tighten the hose clamps securely.
  3. Install any remaining components, then refill the cooling system.
  4. Start and run the engine until it reaches normal operating temperature while checking for leaks.

Posted on Nov 03, 2009

Testimonial: "thank you very much on the solution, didn't take as long as i expected!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replace power window regulator passenger side on acura 1997 2.2 cl still does not work.


Did you test for B+ voltage in the circuit , won't work without it ? There are videos on you tube on how to trouble shoot power window electrical circuit . Suggest you try testing !

Jul 19, 2016 | Acura Cars & Trucks

1 Answer

Power window won't go up


You have to replace a broken window regulator

Go to You Tube Video & see if you can find door
panel removal

Mar 07, 2013 | 1998 Acura CL

1 Answer

1997 acura 3.0 cl fuel pump relay


Iook drivers side on left under the dash.

Feb 23, 2012 | 1997 Acura CL

1 Answer

Have 97 acura won't stay charge changed battery


the battery wont stay charged? if youre putting in a fully charged battery and your car runs, but then the battery slowly dies, the problem will be your alternator. the alternator is what maintains a car batteries charge. try replacing the alternator. hope this helps.

Aug 15, 2011 | 1997 Acura Integra Type R

1 Answer

Window won't go up


yes, ur cable on the drivers window regulator is binding , stretched , and or broken(krinkle noise)..i use to own a c.l 3.0 v6 with the same problem...replaceing the regulator and motor assembly fixed the window...

Apr 20, 2009 | 1997 Acura CL

1 Answer

Acura legend passenger windows wont go down


PASSENGER MASTER SWITCH TURNED OFF ON DRIVERS DOOR WINDOW SWITCH PANEL?????

Mar 30, 2009 | 1992 Acura Legend

1 Answer

1993 Acura Integra drivers side window won't go up or down


needs new window regulator. common problem for this car

Oct 16, 2008 | 1993 Acura Integra Hatchback

Not finding what you are looking for?
1997 Acura CL Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...