Question about Mitsubishi Lancer

1 Answer

Ignation coil 2and3 no ignite - Lancer Mitsubishi Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Switch 2 & 3 to 1 & 4 & see if problem follows coil. If so, bad coils.

Posted on Apr 21, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a wiring diagram of a 1960 ford f-100 6 cylinder ignation coil


I don't have wiring diagram for that year.
I don't mind talking to you.
The positive side of the coil gets voltage from ignition switch, the negative side of the coil goes to distributor and ignition points on a points type system.
Some makes and models, when cranking, everything gets full battery voltage. When it starts and you release the key it springs back to the run position. In the run position, voltage to the coil may go through resistor block or resistor wire, the purpose is so the points on a points ignition doesn't have to deal with full battery voltage all the time. Helps the points last longer.
Just my opinion.

May 30, 2017 | Ford Cars & Trucks

1 Answer

How to timing nissan cifero a32 2and3 coil no signal,.


images for nissan cefiro vq20 timing

P1320 Primary Ignition Signal Fault Testing and ... - YouTube

? 12:27
www.youtube.com/watch?v=kpFzunNeAaY
Aug 15, 2014 - Uploaded by CarsNToys This was performed on a 1997 Nissan Maxima. ... Code P1320 is indicated when ignition signal in the primary circuit (of the power transistor - built into ..... This test is performed at the ECM inside the car, not at the coil itself.

Sep 27, 2015 | Nissan Cars & Trucks

1 Answer

Which is the hot wire on the ignation coil of an 01 ram 1500?


Use a circuit test light and turn the ignition on and check both wires at the coil to see which one lights the test light.

Feb 12, 2015 | Dodge Ram 1500 Cars & Trucks

1 Answer

Where is the distributor cap on a 1998 kia sportage?


the Kia does not have a distributor, let alone a distributor cap, the engine is equiped with a ignation coil at each cylinder, there is a crankshaft and camshaft sensor that send signels to the onboard computer system then the computer sends the signals to the ignation ignator it then sends the signals to the coils at each cylinder. a much better system then a distributor.

Jan 04, 2012 | Kia Sportage Cars & Trucks

1 Answer

I have a plymouth breeze 1999 model 2.4 engine.It is not firing on pistons 2 and 3. On top of that ,the ignition coil pack on the 2and3 pistons is getting so hot so that the rubber on the two points is...


this could be the ignition coil on the 2-3 side of the coil.inspect the connector on the coil to make sure it is good.if the coil has been this hot replace it(used one)as there will be other internal damage to it.these coils are grounded through the computer and supplied power with the key in the on position.the computer grounds the circuit for the cylinder that is to be fired.these also have coil drivers in the computer which may have shorted out.have the system checked out first before replacing parts as if its a shorted driver then it will take out the replaced coil.

Apr 27, 2011 | 1999 Plymouth Breeze

1 Answer

What happen if a ignation ciol is not workeng


if an ignition coil is not working you will get no spark to the spark plugs to test the coil unscrew one spark plug and push it in the rubber boot and hold it with pliers to motor or ground and have someone start car preferablly at night you should see a bright blue spark across spark plug that means coil is okay good luck

Dec 10, 2010 | 1998 Mitsubishi Eclipse

1 Answer

What is an ignation tune up for a 99 Merc. Gnd.


A full ignition tune up would be new spark plugs and wires.A cap and rotor if it has those. Do any fuel system cleaning before changing the plugs.

Jun 22, 2009 | 2001 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...