Question about Nissan Maxima

1 Answer

Flywheel sensor what is the functions of flywheel sensor for nissanmaxima

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 249 Answers

Hi
In laymans terms this sensor is telling the ecu when to start the firing sequence to the coil / coil packs.
on certain vehicles it it also a speed sensor too.
Generally, if there is a fault with this sensor or the wiring to it...the car will not start (no signal).
cheers
Roger

Posted on Apr 21, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 INTREPID WITH 2.7 ACTS LIKE IT HAS A REV LIMITER AT 2500 RPM.HAS NEW CKPS AND CMPS. HELP,,,,,,


It should not be hitting the flywheel. You need a professional to look into this problem with a full function scanner to watch the crank sensor signal in real time.

Feb 22, 2017 | Cars & Trucks

1 Answer

What is the function of a crankshaft sensor


The sensor takes readings off of the flywheel and sends signals to the ECM allowing the car to run Most of the time replacing the sensor will solve your problem unlees you have a wiring issue or the flywheel is damaged but that is unlikely

Jan 26, 2014 | 2003 Nissan Primera

1 Answer

Passat crankshaft sensor


Hi. The amx does not ahve a flywheel pick up. the crank sensor g28 is on the side of the block. The flywheel have offset bolts so can only be fitted in the correct position. The best way to set tdc is with a special tool that goes into the side of the block at g28 sensors hole, or to set tdc with a dial gauge on cylinder 1.

Jan 12, 2014 | 2002 Volkswagen Passat

2 Answers

Crank position sensor is hitting flywheel flywheel got damaged somehow can I bend it down with out a problem or is a new one a must need


What type of car is this..but to answer your question the flywheel would have to be out of round to make contact with the crank sensor i suspect you have a cracked or broken flywheel most of the time they will break at the center of the flywheel where the crankshaft attaches to the flywheel and would still drive for some time

Dec 10, 2012 | Cars & Trucks

1 Answer

Cranksensor trouble on nissan navara 2006


there is almost no way to miss align the flywheel! did you checked side by side for proper fit and all the slots matched , if you didn't i would get one fro the same place and match the old one, Also did you remove the sensor before replacing the flywheel? if you didn't you may have a broken sensor.

Apr 07, 2012 | 2006 Nissan Navara 2.5

2 Answers

2005 nissanmaxima fuel gauge went haywire


the gauge connections must be loose or adrift

Jul 05, 2010 | 2005 Nissan Maxima

2 Answers

Jeep spits and sputters, runs good for a few minutes then starts to sputter. has new plugs,wires,coil,throddle position sensor,cylenoid, fuel filter,and still runs bad.


Have you scanned it for codes. The is a crank shaft sensor that could also be the problem. It will set a code. It is located (sitting in drivers seat) at 2:00 on the bell of the trans bolted to the motor. It is a hall effect switch that reads spaces on the flywheel. If you have had any trans work done they may have buggered up the spaces on the flywheel. Or it may be the sensor. Also have you done a good fuel injection cleaning and check each injector to see if it si functioning. Put a long screw drive one each one or a stethoscope if you have one and see if it is clicking regularly.

Aug 16, 2009 | 1996 Jeep Cherokee

1 Answer

Check Engine light came on and car stalled


Crank Sensor usually have two function,1st the sensor sense the rotation of the flywheel and picks up by the sensor than the sensor send a sigle to your computer telling your computer to send sparks and fuel to to the engine. When sensor goes bad engine quits running, sometime check engine lights come on as computer is not sending no fuel or sparks. Some car has two sensor, one for the fuel and one for sparks. The sensor usually locate next to the flywheels near the main crank. Some are difficult to get to; others are easy. 4cyc on foreign are easy to get to compare to domestic. V6 front wheel drive I find it difficult and V8 rear wheel drive are better. If you plan to keep the car and fix it yourself, the best thing to do is invest and purchase Chilton Repair Manual if planning do it yourself, it will save you lots of money in the future. On 96' breeze should be a breeze to fix, from experience working on Dodge and Chrysler are fairly easy to work on.

Jul 08, 2009 | 1996 Plymouth Breeze

1 Answer

Crankshaft Sensor


what ever u mounted fom the old flywheel was not a magnet....the magnet is internal to the cranksensor and the flywheel slots trigger the sensor....whatever you attached maybe causing this code

Oct 14, 2008 | 1998 Dodge Ram 1500 4WD

1 Answer

Correct flywheel installation '90 240 B230 w/5 SPD transmission


you should have index holes on the flywheel this is to keep the balance of the crankshaft of the motor. the sensor on the back is the knock sensor. your index hole on the flywheel should line up with the holes on the crank. in most instances they should only fit one way. also make sure you put the right side facing the engine. this is important other wise you won't be able to connect the trans and the starter won't match up right.....please rate..thanks

Sep 20, 2008 | 1990 Volvo 240

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...