Question about Renault Kangoo

Open Question

Front window wiper arms do not lift up - Kangoo Renault Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

LT1Rob
  • 55 Answers

SOURCE: how do you lift wiper arm to replace blade on

turn the key on, then turn the wipers on. Time it just right to turn the car off when the wipers are all the way vertical on the windshield. Now you should be able to lift the wiper blades up.

Posted on Mar 14, 2009

  • 54 Answers

SOURCE: remove front wiper arms. Lift arm, slide out

Just pry them off. Make sure the tab is out the whole way. Sometimes they can be tough to get off. Spray with wd40 it should aid in getting it loose. You could even tap it a few times with a rubber mallet or a light hammer, just be careful. Good luck if this helps let me know.

Posted on Jun 19, 2009

  • 477 Answers

SOURCE: lifted thewindshield wiper arm to clean window now i cant get it togo down this is mercedes 300e

push down harder than you think is safe. it'll go CLICK back
it takes a good amount of force to bring it down. You need to push pretty hard ,put a rolled up cloth under it to protect the windshield and the arm's mechanism as well.

Posted on Sep 14, 2012

  • 1010 Answers

SOURCE: Wiper arm doesn't move

Check the arm nut, probably is loose, if not check the arm mechanism

Posted on Mar 20, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove wiper arm?


raise the arm off the window, lift the plastic cover at the end of the arm where it attaches to the car, lower the arm and remove the nut that holds the wiper to the vehicle. make sure you put the wiper back in the same position when you fit it back on the car or your wiper will be out of sync with the other wiper.

Jul 22, 2014 | 1995 Oldsmobile Achieva

1 Answer

Adjust wiper arm


You should be able to unbolt the arm and physically move it on the post. See if there is a cover over the post and a nut underneath.

Jan 25, 2014 | 2009 Saturn VUE

1 Answer

How to take off the rear windsheild wiper on a 94 grand cherokee


You will need a 13-inch wiper blade for the rear window. 1 - When removing the wiper blade lift the wiper arm away from the window. ----- 2 - With one hand holding the wiper arm press the small tab on the underside of the wiper blade where it meets the wiper arm. ----- 3 - Slide the wiper blade off of the arm by pulling the center toward the bottom of the arm.----- 4 - Lightly lay the wiper arm on the window.----- 5 - Prepare your new wiper blade by taking the curved part of the plastic clip and line it up with the curve of your wiper arm. ----- 6 - Lift the wiper arm and press it through the center of the wiper blade up and over the plastic clip. 7 - Pull the wiper blade up until it clicks. Place the arm back on the window.

Jan 11, 2012 | 1994 Jeep Grand Cherokee

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Can't remove rear wiper to replace on 96 caravan


Lift wiper arm from rear window. then release latch that holds the blade to the wiper arm.( It's small tab)

Jan 16, 2010 | 1996 Dodge Caravan

1 Answer

Remove front wiper arms. Lift arm, slide out


Just pry them off. Make sure the tab is out the whole way. Sometimes they can be tough to get off. Spray with wd40 it should aid in getting it loose. You could even tap it a few times with a rubber mallet or a light hammer, just be careful. Good luck if this helps let me know.

Jun 19, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Bad wiper motor on 1996 dodge grand caravan


According to the Haynes repair manual Chapter 12:

1. Disconnect the negative battery cable
2. Detach washer hoses, lift the wiper arm covers and mark the wiper arm locations on the pivot shaft for later re-installation. Remove the wiper pivot nut and remove the wiper arms.
3. Remove the cowl cover (from chapter 11)
3a. Remove the wiper arms then remove the screws that hold the lower area of the cowl cover to the wiper module.
3b. Disengage the quarter turn fasteners that hold the outer ends of the cowl cover to the wiper module.
3c. Open the hood and release the wing nuts that hold the front of the cowl cover to the wiper module.
3d. Close the hood but do not latch it. Now remove the outboard screws and lift the cover up enough to get to the washer hose.
3e. Disconnect the washer hose from the right washer nozzle. Close the hood but do not latch it. Lift the cowl cover toward the windshield and off the vehicle.
3f. Installation is the reverse of removal
4.Open the hood. Disconnect the wiper motor electrical connector.
5. Disconnect the windshield washer hose from the coupling inside the unit. Disconnect the drain tubes from the bottom of the wiper unit.
6. Remove the wiper unit mounting bolts. (Picture appears to be three (possibly allen head) bolts)
7. Remove wiper unit.
8. Installation is the reverse of removal. Wiper blade and wiper arm adjustment is measured with the wipers parked; correct adjustment is the lower wiper arm approximately 1.5 inches distance from the cowl cover and the upper arm approximately 2.5 inches from the lower arm. Operate the wiper motor and check that the wiper motor parks when the wiper switch is OFF.

Mar 21, 2009 | 1996 Dodge Grand Caravan

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...