Question about Jaguar XF

Open Question

Fuses for an XF

Fuse for wiper motor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: 2004 Sebring -- Opening the under hood fuse box.

put cold water over them not hot

Posted on Jan 19, 2009

Ad
  • 16 Answers

SOURCE: my wipers don't work and my fuse box isnt labeled.

there is a diagram of the fuse box either on the inside of the driver door or on the lid that u take off the fuse box

Posted on Mar 12, 2009

  • 188 Answers

SOURCE: 2001 Hyundai Elantra Windshield Wipers wont work.

give the mottor a few taps and spray wd40 in it if you can it releases things thats stuck. also make sure all movable parts are moving freeely. sounds silly but can catch on things. cables are not squashed and the like.

Posted on Mar 26, 2009

  • 718 Answers

SOURCE: Rear wiper Ford Explorer 1998 won't work.

Look for the fuse for the rear wiper motor is a 15 amp mini-fuse , in location # 8 of your POWER DISTRIBUTION BOX in the engine compartment. Check in the PD BOX for; - relay # 8 is the rear wiper down relay , and - relay # 10 is the rear wiper up relay .

Posted on May 18, 2009

  • 1 Answer

SOURCE: the windshield wipers do not work on my Jaguar XJR

I have a 1999 XJ8. Same setup as yours, with very minor differences. I had the same problem, turned out NOT to be fuse, OR bad relays, OR wiper motor, OR Body Processor Module. It was simply a loose connection at the body processor module below the Glovebox. I Literally jiggled the wires, and it started working again, and has been ever since. I have the Shop Manual, Technical ability, and Tools available to test all of the circuits involved, and went forth with printing out the wiring diagrams, and step by step eliminated each, until I decided to give the connection a jiggle, JUST BEFORE replacing the Body Processor Module (which would have been expensive)

Test 1:
Try the jiggle trick. Should be able to access harness just below, and behind the left of the glovebox. touch around up there, but don't be a brute, as you MAY break stuff.

Test 2:
Check Fuse under hood, (#22) Should be a 30A fuse

Test 3:
Swap the relays located on the drivers side, just behind the radiator. One is for Wiper motor run, the other is for wiper motor high speed.

Test 4: Jumper Pin 3 & 5 on the LEFT relay (drivers left) (please remove relay first). This should turn the wipers on, regardless of whether or not the computer is telling it to run. If wiper does not turn on, check fuse, or replace wiper motor.

That's all I've got.... Hopefully this works for you.

Posted on Jul 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

My wiper fuse keeps burning out


If your wiper fuse keeps burning out, your wiper motor might be failing which causes too much amperes required to turn the motor which in turn trips the maximum rated amperes of the fuse.

Follow the wiring of that fuse to your wiper motor to make sure the wiring is not nicked and grounding to the metal. Once you confirm that there is no shorted wire, disconnect the wiper motors wiring connector. Fuse a new fuse and if the fuse does not blow anymore then you isolated the problem which is the wiper motor causing the fuse to blow. Fix or replace the wiper motor.

When diagnosing blown fuses, I usually temporarily replace any fuse in a vehicle with a circuit breaker type fuse. If there is still a short somewhere in the wiring or the component itself in line with the fuse, the circuit breaker fuse will just trip and I just reset it again after I fix the problem. An advantage of keeping to replace a blown fuse while diagnosing.

Oct 04, 2015 | Cars & Trucks

1 Answer

Which fuse or relai controls the wipers motor?


The front wiper motor receives power through the 25A WIPER FUSE in the center console fuse block.

The rear wiper motor receives power through 20A RRWPR FUSE 32 in the center console fuse block.

Jun 17, 2014 | 2005 Pontiac Aztek

1 Answer

Wiper motor montora sport suv keeps blowing fuse


dis-connect wiper motor and replace fuse and try switching wiper motor on if fuse does not blow motor faulty and shorting out and causing fuse to blow.if still blows fuse must be a short in the wiring from wiper motor plug back to wiper motor switch.

wiper motor proberly faulty

May 01, 2011 | 1999 Mitsubishi Montero Sport

2 Answers

Winshield wipers arent working, already tried to change fuses is there more than one fuse box to check


did you check the wipers motor relay? is in the same fuse box in engine compartment.Thanks

Mar 28, 2011 | 2001 Ford Focus

1 Answer

Wiper motor stopped working. I need a wireing diagram for the wiper motor , switch and relay


Wiper motors usually do not have a relay, they are operated directly from the switch. Before you look at wiring, check the fuse, wiper motors are notoriously reliable and something like a switch will go long before the wiper motor. The fuse must be in the main fuse box. The position and function of the fuses is normally marked on the inside of the fuse box cover and also in the owner's handbook. If you don't come right with these, work your way through the fuses looking for a blown one. To ease your search the wiper fuse it should be around 15 to 20 amps.

Mar 15, 2011 | Chevrolet Corvette Cars & Trucks

1 Answer

Windshild wipers stop working


CHECK FUSE IF FUSE GOOD.HOOK A JUMPER WIRE TO GROUND AND GROUND WIPER MOTOR.TURN WIPER SWITCH ON IF WIPERS WORKS YOU HAVE TO FIX GROUND CONNECTION. IF WIPER STILL DONT WORK.REMOVE THE COWL COVER.TURN WIPER SWITCH ON TO SEE IF POWER GOING TO WIPER MOTOR IF YES.REMOVE WIPER MOTOR HOTWIRE IT.IF WIPER MOTOR DONT WORK REPLACE IT.IF WIPER MOTOR DO WORK CHECK FOR BINDING OR DAMAGE LINKAGES.IF POWER NOT GOING TO WIPER MOTOR AND FUSE GOOD.WIPER SWITCH FAULTY OR IT HAS BROKEN WIRE FROM SWITCH TO WIPER MOTOR.

Oct 04, 2010 | 2002 Toyota Avalon

2 Answers

Front wipers stopped working but you can hear the motor run also


If the wipers were buried under snow/ice or frozen to the windshield, you may have blown the red 10 amp fuse located in cavity 9 in the fuse block located on the bottom left side of the instrument panel near the parking brake pedal.
In order of easiest to check:
1) ensure wipers not frozen to windshield.
2) ensure wiper arms are not loose on the pivot stud,
3) check the red 10 amp fuse.
You stated that "you can hear the motor". Which motor do you hear? The engine or the wiper motor?
If you hear the wiper motor, then the fuse is alright. Try 1) and 2) above.
PT Stanley

Jan 20, 2009 | 1998 Dodge Grand Caravan

1 Answer

Wipers wont work


1.  Turn on your wipers and pop your hood.   2.  If you hear you wiper motor, then you do not need to check your fuses. 3.  If your wiper arms are moving freely, then your linkage from the wiper arms to the motor is disconnected and possibly broken.   4.  If the problem is electrical, do the following:      1.  Check the fuse, and check for power at the fuse.      2.  Check the wiper motor for ground. For a complete circuit, you need power going in and ground               coming out.  Check electrical connections for corrosion or poor connections.       3.  Get a wiring schematic and trace power to the wiper motor starting at the fuse box in the                       following order:           Fuse box           wiper switch           wiper motor      4.  In the rarest of cases a wiper motor or wiper switch is at fault.  I do not recommend replacing                 anything unless you have proof that the part is faulty. (ie. power going into the switch but nothing           coming out.)       

Dec 21, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...