Question about Cars & Trucks

Open Question

Replace front hub with wheel bearing - Cars & Trucks

Posted by Anonymous on

  • Richard Gagnon
    Richard Gagnon Apr 21, 2014

    Kind of car will help a lot

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

  • 23 Answers

SOURCE: how do u remove front wheel bearing

Take off the wheel, then the brake caliper, noow you have the roter. in the center is a cap, the center cap, this comes off by pruing it off with a screwdriver. Inside that a retaning pin, take that out, then a nut cover, and nut with grooves in it from where you took out the pin. It is good to mark about where it was so when you put it together, you will not overtighten it.

Take that nut off, then you should be able to take off the whole assembly, bearings and all. If this is a sealed unit, you have to but a roter that will have the guts already inside it. make sure you clean off all of the old grease, you are going to replace critical parts, so you need new grease for them. Also make sure your spildle is not grooved, if so haw bad, you might replace it to if all gualled up.

on a sealed unit you just reverse the steps from taking it off.

if not you have to knock out the old races in the caliper, the one side by a wide screwdriver and hammer, there are pullers, but from the way it sounds, it is in there tight. Just be carefull not to kill the sides and rotate it around when doing this. once it is out, do the other side, find a socket that size, one thak will fit in the race almost to the edges and beat it out. now make sure the caliper is in a flat surface, and use a blanket or something toi avoid knicking the thing.

once both are out, just reverse the process, grease the inside just a bit and when you put the race in use a socket that is the size of the race, and beat it in evenly.grease your bearings, make sure you do one side at a time, and putting them back on the spindle is a cake walk compared to what you just have done.

hope this helps

Posted on May 26, 2009

burdfrenzy
  • 348 Answers

SOURCE: Is it hard to replace the front wheel bearing hub

Its a big pain. The hub is rusted on tight and has to be beaten off with a mini sledge. Go to your local AP store and look it up in a repair manual to see what you are in for.

Posted on Oct 15, 2009

  • 98 Answers

SOURCE: How is front wheel bearing replaced on a 2001 Volvo S40?

most front wheel bearings are pressed in you half to take the whole control arm off pull out the hub press out the bearing grease the new one and press it in its best to take it to a machine shop do not try pressing it in yourself

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

How to replace front wheel bearing?


old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes



  1. Before servicing the vehicle, refer to the Precautions section.


  2. Remove or disconnect the following:



    • Front wheel


    • Brake caliper and rotor


    • Locking hub or hub drive flange, if equipped,(it is)


    • Hub grease cap, if equipped


    • Wheel speed sensor, if equipped (ABS)


    • Wheel bearing lockwasher


    • Wheel bearing locknut (ring) and inner washer


    • Wheel hub and bearing assembly (slide hammer?)


    • Wheel hub oil seal


    • Wheel bearing oil seal


    • Snapring




  3. Press the wheel bearing and race out of the hub.


reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

Jun 26, 2014 | 2000 Suzuki Grand Vitara

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

Directions replace front wheel bearings on a 1985 nissan stanza?


996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Jun 23, 2009 | 1985 Nissan Stanza

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

1 Answer

Chey aveo front hub bearing what is this?


yes front wheen drives have hub bearings. Most of them need the hubs to be pressed apart to replace them. the hub bearing supports the end of the CV drive shaft closest to the wheel. hope that helps.

Mar 17, 2009 | 2004 Chevrolet Aveo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...