Question about 2006 Nissan Pathfinder

Open Question

Replacting rear door handle R51

How do I get the door panel of the rear right hand door, to replace exterior handle with aftermarket handle?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 112 Answers

SOURCE: 2002 Nissan Altima Exterior Door Handle

Look at the inside of the door directly behind the door handle. There should be a hole about 15 mm wide.
Just enough to get a small socket through.
Make sure the window is up.

Posted on Feb 03, 2009

Ad
  • 1 Answer

SOURCE: cant open right rear pasenger door 2005 pathfinder

i started by removing ashtray and the screw underneath. it would be easier to remove rear seat as access is not so good to move around. wind window down, then carefully pull from top of trim, it should come away fairly easy. the trim is held on by push in clips but you need to careful as they break easy. behind the inside door handle is a plastic backing plate which i found easier to remove first. now the outside handle can be undone and i simply pulled the cable and the door opened. the cable was broken where it joins the handle so a new cable is needed.

Posted on Jul 18, 2009

michigan man
  • 3533 Answers

SOURCE: I need to replace the exterior driver's side door

yes you are right you have to remove the inner door panel give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your local nissan dealership in the part department and they be able to print out pictures and diagram showing you how to replace your door handle wish you the best of luck Michigan Man.

Posted on Oct 22, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

  • 1 Answer

SOURCE: how to replace exterior door handle on 2007 Versa.

You need a Torx head screwdriver T25. Open the door and on the side of the door is a small black grommet, remove grommet, inside is the torx screw you need to loosen for the lock mechanism to move. you dont need to remove the screw just loosen enough to move the lock assembly around. Once loose enough, install the door handle and tighten lock assembly back and put grommet back.
Here is a picture if you need a bit of visual clues.
http://img266.imageshack.us/img266/1218/versadoorhandlefix.jpg
_69.jpg

Posted on Nov 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace and fit an extrior RH door handle to a 1995 Suzuki Baleno?


Open the door and remove the door panel with a special tool. Take out the screws on the door panel and any knobs or latches. Remove the panel. Cut the dust or noise seal, it is a messy liner that looks like paper or plastic. Remove the window hardware if you cannot get to the door handle screws from the openings in the door. Remove the window if you do this. Then you can replace the handle. Be mindful of the sharp edges that are present on the door.

Sep 12, 2014 | Cars & Trucks

1 Answer

Replacing Exterior Door Handle on 1989 burb


if you can not get to the handle at all you will need to go from the inside. if that is the case try and pry the top of the door panel off without distorting the panel. then with a flash light look down inside the door and you should see a metal rod, try pulling the rod up or down which should open the door! hope this helps

Feb 22, 2014 | GMC Cars & Trucks

1 Answer

How do I repair the exterior door handle on a 1999 Toyota Camry ? Will it be necessary to replace the entire door ?


No the door handle is easily replaceable. you do have to remove the door panel and roll the window all the way up. 2 10mm nuts inside the door cavity and one bolt on the door jam near the lock mechanism. These handles are made of plastic and degrade and break easily after 3 or 4 years. Every toyota owner has to deal with this at some point. I also recommend buying the new handles on ebay as opposed to the dealer. The aftermarket handles are better quality than the original and MUCH cheaper. They are ALWAYS available on ebay.

Aug 02, 2012 | 1999 Toyota Camry

1 Answer

Were does the LH mirror on a 2011 f-250 connect. Removed mirror but disconnect is located some were in door or body. need to know what needs to be removed to gain access


  1. Remove the front door trim panel.
  1. Position aside the front door watershield to gain access to the exterior rear view mirror control switch electrical connector.
4.Disconnect the exterior rear view mirror control switch electrical connector
ganyapr_7.jpg
as you see you have to remove the door panel to have access to the electrical connector in case that you dont know how to do it here are the instructions

NOTE: Left front door trim panel shown, right front door trim panel similar.
  1. Remove the sail panel.
    • If equipped, disconnect the electrical connector

  2. If equipped, lift up and remove the exterior rear view mirror control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, lift up and remove the window control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, remove the window regulator handle.
    1. Position the window regulator handle cover aside.
    1. Remove the window regulator handle screw and regulator handle
5.Remove the door trim panel center screw cover
6.Remove the 2 door trim panel center screws
7.Remove the 2 door trim panel lower screws
  1. NOTICE: Do not pull directly outward on front door trim panel as damage will occur.
    Remove the front door trim panel.
    • Lift upward to remove the front door trim panel.
  1. NOTICE: Insert the lower panel tabs first or they can break when installing the front door trim panel.
    To install, reverse the removal procedure

Feb 20, 2011 | 2011 Ford F-250 Super Duty

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

Need to replace exterior door handles


take off door panels and get your hand inside. philips head and 8mm socket

Jul 21, 2010 | 1999 Chrysler Sebring

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

2 Answers

Need instructios to repair 1997 Toyota Camry Broken Exterior Door Handle


Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

May 30, 2009 | 1997 Toyota Camry

1 Answer

How to replace '96 Ford Explorer driver side exterior door handle


You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Jan 19, 2009 | 1996 Ford Explorer

1 Answer

Problem with passenger door handle (94-97 Accord)


the assy. that keep therod for openeing the door up is whats wrong worn out needs replacing , yu will have to take panel off to repair though good luck

Aug 03, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2006 Nissan Pathfinder Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...