Question about 2000 GMC Sierra

Open Question

Keyless remote will not work even after replacing battery

Bought new battery for 2 keyless remotes.neither one would work even after replacing batteries

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: programing keyless remote

To Program a new remote you must get in your vehicle, close all doors hold your unlock button down.while holding the button down turn your key on and off two times.at that time your locks will all cycle.Then with your keyless remote hold your lock and unlock buttons till the locks cycle .

Posted on Sep 18, 2008

Ad
  • 3 Answers

SOURCE: Keyless remote entry does not function, panic button does.

This link will take you to very good instructions try it worked for me www.wikihow/program-a-keyless-entry-for-a-chevy-silverado this works on GMC models also.

Posted on Apr 06, 2009

Molson02536
  • 3854 Answers

SOURCE: Driver 2 Remote Keyless Entry (RKE) not working, Driver 1 is OK

To resynchronize your transmitter, stand close to your vehicle and press and hold the LOCK and UNLOCK buttons on the transmitter at the same time for seven seconds. The door locks should cycle to confirm synchronization. If the locks do not cycle, see your dealer for service.   I hope this works and good luck

Posted on Apr 08, 2009

  • 55 Answers

SOURCE: Keyless remote Problem for Yukon Denali 2005

Have your dealership test the remotes for you, they will also use a "Tech-2" to re-program it and should not charge you to do so. "I know mine does not" The "puddle" lamps come on when you un-lock the doors with the remote."If they are enabled in the options on your dash information center or "DIC". "See owners manual for info on that". As far as the DRL's make sure your bulbs are good because they are known to blow out. But the remote should not have anything to do with those.Hope that helps a little?

Posted on May 05, 2009

  • 15 Answers

SOURCE: keyless entry remote quit working. Just purchased

Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why would my battery be draining after trying to program a keyless entry remote with no luck


Just guessing, but maybe your car is still searching for signal from remote? Kind of like when our phones are roaming for signal...

Oct 10, 2017 | Cars & Trucks

1 Answer

Keyless remote wont work


Many times if you purchase a used vehicle, the car lot only provides the key because they do not want to spend the money to purchase a key fob. A 2006 Lancer either has a 2 or 3 button keyless entry remote which you can find here: http://replacemyremote.com/
Keyless Entry Remote Fob Replacement

Feb 08, 2014 | Mitsubishi Cars & Trucks

3 Answers

Change battery keyless remote


Replace battery very expensive to get new one they are button batterys get hi power ones

Nov 03, 2013 | Chevrolet Equinox Cars & Trucks

1 Answer

2008 HHR Remote Starter not working


Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Guessing will not fix this .

Jan 12, 2018 | 2006 Chevrolet HHR

1 Answer

My remote start and keyless entry remote only works up to 5 feet away how do i extend the distance. i bought new remotes and had them programmed but still no distance


On my cars this has always been a remote battery replacement issue, weak battery equals weak signal causes short range. However you say you bought new remotes and they must have had new batteries in them. Did someone put some metal foil shielding around the receiver?I think this would have to be some type of bad receiver issue.

Oct 13, 2010 | 2005 Buick LaCrosse

2 Answers

Keyless Remote Won't Work - But Car Starts


The remote receiver unit is located in the rear view mirror. This may be faulty. Since the car is new (less than a year?) you still may have the factory warranty.

Jan 16, 2010 | 2009 Volvo S40

1 Answer

Keyless remote


hi, i hope this helps..as far as the tire monitor, it might solve it, not likely...and if your keyless remote is not programmed to your car, it will need to be, however there are alot of independent shops that will have the interface computers needed to help ya and cheaper..

May 27, 2009 | 2006 Pontiac G6

Not finding what you are looking for?
2000 GMC Sierra Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...