Question about 1994 Jeep Grand Cherokee

Open Question

Crank sensor in a jeep grand Cherokee 1994 v-6

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Jeep Hesitates. P0303 code

Check the cylinders Commpression. over 115 psi is good, 120 psi is normal.

Posted on Sep 17, 2008

dburns60
  • 410 Answers

SOURCE: where is the map sensor located? 1994 jeep grand cherokee

Go half way between the air cleaner box and the "carburetor". Up the 4" black air pipe, a wire harness plug plugs into the MAP sensor there. Also called MAS air flow sensor.

Posted on Oct 05, 2009

  • 306 Answers

SOURCE: speakers for 1994 jeep grand cherokee

6.5" in all the doors dash is wierd. 2.75" but i have been able to squeez in a 3.5"

Posted on Feb 04, 2010

Testimonial: "thank you so much, that helps me out as lot"

  • 834 Answers

SOURCE: how do i replace the crank position sensor on a

If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Posted on Jun 21, 2010

jturcotte
  • 7754 Answers

SOURCE: Need to replace Crank Sensor - can't locate on

at the rear of the engine by the tranny. see pic below.

jturcotte_337.gif

Posted on Nov 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

2 Answers

What is the plug on top of a transmission for in a 94 jeep Grand Cherokee AWD?


Being a 94, it's probably a speed sensor. Newer ones are in the transfer case.

Apr 12, 2015 | 1994 Jeep Grand Cherokee

1 Answer

I have a 1994 jeep grand cherokee and it always starts up, but sometimes it just shuts off randomly while I'm driving and after a few minutes of rest turns back on, the battery will still be worki


Install a new crank shaft sensor. I had the same problem with my wife's Jeep. It would run fine fore days at a time then quit. When the crank sensor goes out their is no spark or injection of fuel into the engine. This is a Hall Sensor. They can be intermittent, and affected bu heat. If your Jeep will not start, try freeing the sensor and see if it starts. Cold Freeze is used in electronics to test

Apr 17, 2013 | 1999 Jeep Grand Cherokee

1 Answer

I HAVE A 94 GRAND JEEP CHEROKEE IT KEEPS DIEING ON ME WHILE IM DRIVEING DO U THINK YOU CAN TELL ME WHAT IT COULD BE? ALL THE LIGHTS AND RADIO STAY ON WHEN THE CAR DIES!


The crank sensor on that body style Grand Cherokee is known to cause the shutdown while driving problem. Have it checked out.

Sep 01, 2011 | 1994 Jeep Grand Cherokee

1 Answer

1994 jeep grand cherokee won,t start. no fire on the spark plugs.


these jeeps have a problem with the crank position sensor which cause most all of the issues with no spark condition, it is located on top of the transmission where it bolts to the engine(bellhousing)

Jan 30, 2011 | 2000 Jeep Grand Cherokee

1 Answer

1994 Jeep Grand Cherokee that will start sometimes.


you can have a bad coil you can have a bad crank sensor a bad cam sensor a bad throttle posistion sensor etc. if you can have someone do a diagnostic on the car to see if any codes are stored this will give you a good starting point.

Jun 18, 2010 | 1994 Jeep Grand Cherokee

1 Answer

1994 jeep grand cherokee


It should be mounted in the transmission bellhousing. Drivers side on the 6 cylinder and passenger side on the 8 cylinder.

Jun 11, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Changed battery in 1994 jeep cherokee now engine won't start. Tried resetting alarm by unlocking drivers door and hatch door. Still not starting


Do you know how to check codes on your Jeep? Sometimes the crank position sensor goes out but the Jeep will still run until there is an interruption in power to the ECU. I had a 94 Cherokee do the exact same thing. Turn your key in the following pattern: off-on-off-on-off-on. Leave it on and look at the engine light - it will blink out 2 digit codes. If I remember right code 11 is for the crank sensor...

Jan 05, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...