Question about 2002 Jeep Liberty

1 Answer

Is wiring harness already there for power seats in my jeep libert

Is wiring

Posted by on

  • yadayada
    yadayada May 11, 2010

    for what??

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

No, you will have to buy harness' and you probably have to buy different BCM for a liberty that had power seats!!! (BCM=Body Control Module)

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cable used for-- under drivers side seat in a 1998 Jeep Cherokee Sport?


There are 3 cables under the driver's seat.
1) 1 (single wire) goes to the illumination light of the transfer case position plastic lense panel (underside) 2) 1 (single wire) goes to the seat belt harness for the seat belt warning light 3) 1 (multi-wire) goes to air bag sensor located directly under the seat.
Your welcome :-)
Steve

Jun 02, 2011 | 1998 Jeep Cherokee

1 Answer

Seat heaters and electric seats stopped working. Could this be associated with a fuse problem?


check the wiring harness below the seat. The harness includes the power to the driver power seat as well as the seat heaters for both fron seats. My 2003 has a contact issue where it only works when another person puts pressure around the harness and wires (Bad Connection). This happened after 2 years of use with this harness. harness has been replaced 3 times over 7 years

Jan 18, 2011 | 2005 Chevrolet Tahoe

1 Answer

My power seats went out on my 91 model jeep Cherokee and I am having a hard time finding where to replace the fuse. Can I adjust the seat manually if need be??


Yes - but it is not very easy. You'll need to run a wire from your positive battery wire to the motor harness under the seat. Some harnesses have a red,blue,or green wire along with a black. Depending on which package your jeep has and which direction you want to move it depends on which wire you need to tap in to. You may also have luck if you remove the seat switch panel from the side of the seat and run your jumper to the corresponding terminal to move the seat. My 93 has bad switches and so I set my seat where I wanted it and unplugged the motor so nobody can move it accidentally.
Hope this helps and please rate my solution!!

Dec 13, 2010 | 1991 Jeep Wrangler

1 Answer

My Jeep is a 1992 Limited Edition Cherokee and the power seats do not work. I have isolated the problem and need to run a new ground wire but I do not have drawings and do not know exactly where or how to...


Your best ground is the battery negative post. second best is the engine block. Run the new wire to either and you will have a good ground. You have located the ground wire in the seat harness?

Aug 23, 2010 | Jeep Cherokee Cars & Trucks

2 Answers

How and where is the turn signal flashers located?


1999 Jeep Cherokee 4WD 4.0L MFI 6cyl
The Flasher is located in seating area, driver side, located in a wire harness connector which is secured to the diagnostics splice block bracket outboard of the steering column opening underneath the instrument panel.

Also, I suggest check the Service Manual for Jeep XJ Cherokee Electrical Section or the other section HERE

Hope helps with this (remember rated this) Good luck.

Jan 13, 2010 | 1999 Jeep Cherokee

2 Answers

I have two trucks: a 2006 1500 without power seats and a 2003 with power seats. Can i put the power seat in the 2006? do the mounts match up? Is there electric already there?


The mounts will be the same however you may need to take part of the wire harness and switch it to the newer truck. Just make sure you follow the original hook up (maybe take some pix ) and just follow it back to the underside of the dash, this is providing that the wiring is not already there. Good luck, Dana

Aug 23, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Power seat problem


sometimes the wiring harness gets correded and loses contact. check harness especially near connections. failing that, make sure there is power going to units

Jul 08, 2009 | 2004 Chevrolet Tahoe

1 Answer

2003 Chrysler sebring wiring diagram for power and heated seats


Do some checking if you haven't already, the harness may already be there under carpet. If not, you may have to sweet talk a service guy at dealership for the print you need, or try www.alldata.com.

Mar 27, 2009 | 2003 Chrysler Sebring

1 Answer

Replacing electric seats from a 1995 model into a 1997 facelift.


Technically, you can put any seat in any vehicle, as long as it dosen't interfere with anything. (door closing etc) As far as I know, most jeep seats interchange easily, At worst, you may need to drill a hole or two. Important part is before you begin, identify each wire in the harness, making sure that you know which one does what so if the harnesses don't match you can easily switch wires around. Write it down. Don't try to remember if you do great but if you forget, you can burn stuff out!!! If you need to cut wires, don't twist and tape...twist, solder then tape.
Good luck

Mar 15, 2009 | 1997 Jeep Cherokee Country

1 Answer

Help, No Power to power seats


Under the seat there is a plug-in harness, dsisconnect it and see if ther is any power going to the harness, not the seat. then check your fuses under the hood, you should have only one there for your power seats. If that isn't the problem, then replace the motors in the seats.

Feb 07, 2009 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...