2001 Chrysler Sebring Logo
Posted on Jun 19, 2009

2001 Chrysler Sebring LX sedan power locks

My power locks do not work. Fuse is good. Using the key fob to lock it sounds the horn and lights flash, but the door locks to do not work. Also using the lock buttons on the inside of the car do not make them work. Any help would be great as I do tend to carry expensive things on my car and have a fairly pricy after market stereo.

  • in4m8ion Jun 20, 2009

    Thanks! I will definitely try that and get back to you letting you know the outcome

×

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 2 Answers
  • Posted on Jun 20, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Jun 20, 2009
Answers
2
Questions
0
Helped
1513
Points
2

It is a long shot, but I took my door skins off a while back to access the speakers, and when I put the door skins back on my doors wouldn't lock. It was just a dirty contact switch. I took my driver side door skin back off, cleaned both metal surfaces with a rag and it fixed the problem. I believe the switch is on the back of your lock button, it's a thin piece of metal that looks like a pen clip.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to program a new keyless fob with an existing working fob on a 2008 Chrysler 300 LX

  1. How do I program my Dodge key fob without working one?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px; transform: rotateZ(-180deg);">
    How do you program a key fob without original?
    1. Replace the batteries inside the key fobs.
    2. Get inside the car.
    3. Turn on the ignition.
    4. Press the lock button on the remote key.
    5. Listen for a Lock Sound.
    6. Programming additional remotes.
    7. Turn off the ignition.
    8. Step out from your car and test the result. How to program my Chrysler key fob without working one Turn the ignition key to Accessory or "ACC". Turn the ignition key off again, and the door locks will cycle once. Press any button on the key fob 3 times in a row to program it. The door locks will cycle once again once programming is complete. https://northcoastkeyless.com/2008-chrysler-300-keyless-entry-remote-fob-programming-instructions/ the instructions to [program a fob are that you need two or need to have dealer or approved locksmith
0helpful
1answer

Car alarm preventing car from starting

Try removing the alarm system relay, some car alarm has also a fuse on the alarm that you can remove.
Many car alarms unlock by inserting and turning car key while you connect the battery.
0helpful
1answer

I assume the factory alarm was somehow bypassed when they installed the remote start is there a way I can make the factory alarm work when the doors are opened without key,?

To arm content theft alarm.
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The
SECURITY light should flash.
3. Close all doors. The SECURITY light should go off
after approximately 30 seconds. The alarm is not
armed until the SECURITY light goes off.

If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power.
0helpful
2answers

I have a 2004 Chrysler Sebring sedan. I am assuming I have a blown fuse but I cannot find the right one. The interior lights, radio, and power locks don't work. The fuse box panel doesnt tell which...

the radio and interior light is normally a different fuse to the windows the windows will be a 30a and the other a 7.5 or a ten max ,could be a corroded fuse holder in the power supply box under the bonnet
3helpful
2answers

Tire specs for 2001 chrysler sebring

HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16
1helpful
1answer

No Bus on dash

make absolutely sure nothing is maybe not plugged in all the way. like pcm harness.
4helpful
2answers

No power to cigarette lighter, and no fuses designated as such for it 2001 chrysler sebring Sedan LX,

Did you check the fuses under the hood? The cigarette lighter fuse is not located in the fuse box by the passenger door.
7helpful
2answers

Car Radio

I have a 2001 Chrysler Sebring Convertible. The battery died and I jump started it. Now the radio does not work. The only lights are the flashing equilizer lights. Any suggestions?
Not finding what you are looking for?

1,181 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...