Question about 2003 Audi A4 3.0

Open Question

P1142 load detection value below lower limit

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tunde007
  • 2382 Answers

SOURCE: have a 2004 audi tt

Hi, the P0113 means Intake Air Temperature Circuit High Input
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code. There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).
A code P0113 may mean that one or more of the following has happened:

  • Internally failed IAT sensor
  • Faulty connection at IAT sensor
  • Open in IAT ground circuit or signal circuit
  • Short to voltage in IAT signal circuit or reference circuit
  • IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
  • Faulty PCM (less likely but not impossible)


On the issue of the intake manifold inflating, vacuum leaks and torn air boots cause a vehicle to perform poorly. These leaks allow for a lean mixture inside the engine making it work harder upon start up. An air intake boot can be torn or cracked. You need to replace air intake boot.....

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pontiac grand prix 2007 car shutting off, with Start disabled throttle control module.


It doesn't say module , Starting Disabled Due To Electronic Throttle Control !
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position (APP) sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The APP sensors
• The throttle body assembly
• The powertrain control module (PCM)
Normal Mode
During the operation of the throttle actuator control (TAC) system, several modes or functions are considered normal. The following modes may be entered during normal operation:
• Minimum pedal value--At key-up, the powertrain control module (PCM) updates the learned minimum pedal value.
• Minimum throttle position (TP) values--At key-up, the PCM updates the learned minimum throttle position value. In order to learn the minimum throttle position value, the throttle blade is moved to the closed position.
• Ice break mode--If the throttle is not able to reach a predetermined minimum throttle position, the ice break mode is entered. During the ice break mode, the PCM commands the maximum pulse width several times to the throttle actuator motor in the closing direction.
• Battery saver mode--After a predetermined time without engine RPM, the PCM commands the battery saver mode. During the battery saver mode, the TAC module removes the voltage from the motor control circuits, which removes the current draw used to maintain the idle position and allows the throttle to return to the spring loaded default position.
Reduced Engine Power Mode
When the PCM detects a condition with the TAC system, the PCM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The PCM will continue to use the accelerator pedal for throttle control, however the vehicle acceleration is limited.
• Limited throttle mode--The PCM will continue to use the accelerator pedal for throttle control however the maximum throttle opening is limited.
• Throttle default mode--The PCM will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The PCM will perform the following actions:
- Limit engine speed to idle by positioning the throttle, or by controlling the fuel and spark if the throttle is turned off.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The PCM will disable fuel and de-energize the throttle actuator.

DTC P2101
DTC P2107
DTC P2108
DTC P2119
DTC P2120
DTC P2125
DTC P2135
DTC P2138 You need to see which of these codes

Nov 16, 2016 | 2007 Pontiac Grand Prix

1 Answer

How do i fix code poa7f for Honda Civic 2011


DTC P0A7F indicates: Battery Module Deterioration.

General Description
The capacity of the battery module is defined by the upper and lower limits of the battery module voltage.
When the battery deteriorates, the limits of the battery capacity are narrowed. Under specific driving conditions, the battery condition monitor (BCM) module monitors the maximum and minimum voltage of the battery module. The BCM module computes the battery module electrical current value during operation to calculate the battery module capacity. If the calculated value is under the specification, a malfunction is detected and a DTC is stored.

Malfunction Threshold
The battery capacity is less than 10 % of 6.5 Ah.

Diagnosis Details
Conditions for illuminating the MIL
When a malfunction is detected, the MIL comes on and the DTC and the freeze frame data are stored in the PCM and BCM memory.

Conditions for clearing the MIL
The MIL will be cleared if the malfunction does not recur during three consecutive trips in which the diagnostic runs.
The MIL, the DTC, and the freeze frame data can be cleared by using the scan tool Clear command or by disconnecting the battery.


At this point you should bring it into your nearest honda dealer as the IMA battery will require replacement.

Talk to someone at the dealership about the IMA battery in-warranty exchange program.

I hope all this information helps you out.

Jun 26, 2015 | 2011 Honda Civic 1.4

1 Answer

What is a P2404 code mean from a suzuki sx4


Trouble Code: P2404 (2.0L L4 VIN 5 Automatic CVT)
Evaporative Emission System Leak Detection Pump Sense Circuit Range / Performance
Number of Trips to Set Code: 1
Trouble Code Conditions:
EVAP vent valve stuck open: EVAP leak check pressure is lower than -0.14 kPa even if EVAP vent valve is operated from OFF (OPEN) to ON (CLOSE) with EVAP leak detection pump ON. EVAP vent valve stuck closed: EVAP leak check pressure is unstable (difference between maximum and minimum is 0.36 kPa or more) when EVAP vent valve is OFF (OPEN) with EVAP leak detection pump ON. EVAP leak detection pump stuck OFF: EVAP leak check pressure is higher than -0.14 kPa even if EVAP leak detection pump is ON. EVAP leak detection pump flow high: Reference pressure of EVAP leak check pressure is lower than specified value (depending on BARO) EVAP leak detection pump flow Low: Reference pressure of EVAP leak check pressure is higher than specified value (depending on BARO).
Possible Causes:
  • EVAP leak detection pump (in EVAP leak check module) and/or its circuit
  • EVAP vent valve (in EVAP leak check module) and/or its circuit
  • EVAP leak check module and/or its circuit
  • ECM

Jul 11, 2014 | 2010 Suzuki SX4

1 Answer

Starts and switch of automatically problem code P 1275 if camshaft sensor is pulled out vehicle stays idiling but still revs up slow. Engine light stays on.


P1275 Aging of Oxygen Sensor Ahead of Catalytic Converter (Cylinders 1 - 3) - Below Lower Limit

The diagnosis of "oxygen sensor aging" helps to identify oxygen sensors that exceed emission limits because of aging.
During the diagnosis of oxygen sensor aging, the DME control module monitors the period of the sensor signal. With an old sensor, the duration of the period is too long, i.e. it is more difficult for the sensor to diffuse oxygen into the exhaust gas. Reasons for this could be frequent driving in the lower load range (city driving, short distances, etc.) or a contaminated sensor.

Bottom line - you need to replace that O2 sensor.
hope help.

Jul 06, 2011 | 2004 Nissan Pathfinder

1 Answer

Code PE 1259 for Honda Odyssey 1998


Trouble Code Conditions:DTC P0107, P0108, P0135, P0137, P0138, P0141, P1128, P1129 and P1259 not set, engine running in closed loop, and the PCM detected the LONGFT value exceeded the calibrated lean limit value
Possible Causes:
Air leaks in intake manifold, exhaust pipes or exhaust manifold One or more injectors restricted or pressure regulator has failed Air is being drawn in from leaks in gaskets or other seals O2S element is deteriorated or has failed A "fuel control" sensor is out of calibration (ECT, IAT or MAP)

May 31, 2011 | Honda Odyssey Cars & Trucks

1 Answer

Check Engine light code P0432


P0432 - Main Catalyst Efficiency Below Threshold Bank 2
The ECM or PCM monitors the front an rear O2 sensors. The ECM or PCM detects Warm up Catalytic Converter when the sensors are out of specifications.

DTC is set when the ECM or PCM detects rear HO2S value difference becomes closer to value of front HO2S. The ECM or PCM monitors when vehicle speed is 25-60 MPH, load is 22-45 percent and engine speed is 1000-3000 RPM.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Warm Up Three Way Catalytic converter deterioration or malfunction. - Exhaust system leaks. - Loose front or rear HO2Ss. - Front HO2S malfunction. - O2 sensors harness or connectors

Possible solution
- Replaced Catalytic Converter - Replaced rear O2 sensor - Repair wire harness or connectors

Check it ans tell us news.

Jan 16, 2011 | 1999 Dodge Intrepid

3 Answers

A p0301 p1142 p1545


CODE PO301 - CYLINDER NUMBER 1 MISFIRE DETECTED. POSSIBLE CAUSE- BAD COIL - SPARK PLUG - INTAKE MANIFOLD VACUUM LEAK - DIRTY OR FAULTY FUEL INJECTOR. CODE P1142 - DID NOT SEE. CODE P1545 - THROTTLE VALVE ACTUATOR MALFUNCTION.POSSIBLE CAUSE THROTTLE VALVE CONTROL MODULE FAULTY - THROTTLE VALVE IS DAMAGE OR DIRTY - THROTTLE VALVE MUST BE IN THE CLOSE POSITION - ACCELERATOR PEDAL OUT OF ADJUSTMENT. THROTTLE POSITION ACTUATOR IS SHORTING TO GROUND OR POWER.

May 09, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

I have 3 codes that showed up in the computer of my 1995 Ford Windstar


Here is the first half of the codes look till you find the one you have
111 System PASS.
112 ACT sensor circuit grounded.
113 ACT sensor circuit open.
114 ACT sensor is out of Self-Test.
116 ECT sensor is out of Self-Test.
117 ECT sensor circuit grounded.
118 ECT sensor circuit open.
121 TP sensor is out of Self-Test.
122 TP sensor input is less than Self-Test minimum.
123 TP sensor input is greater than Self-Test maximum.
124 TP sensor input voltage is greater than expected.
125 TP sensor input voltage is less than expected.
128 MAP vacuum hose damaged or disconnected.
129 Insufficient MAF input.
136 HEGO sensor circuit indicates system lean (Right HEGO).
137 HEGO sensor circuit indicates system rich (Right HEGO).
139 No HEGO switching (Front Side).
141 Fuel system indicates lean.
144 No HEGO switching (Left Side).
157 MAF sensor circuit open.
158 MAF sensor shorted to power.
159 MAF sensor is out of Self-Test.
167 Insufficient TP input change.
171 Lack of HEGO switching (Rear Side).
172 HEGO sensor circuit indicates lean. (Rear Side).
173 HEGO sensor circuit indicates rich. (Rear Side).
174 Check for diluted engine oil.
175 Lack of HEGO switching (Front Side).
176 HEGO sensor circuit indicates lean. (Front Side).
177 HEGO sensor circuit indicates rich. (Front Side).
178 Check for diluted engine oil.
179 Fuel system at part throttle lean adaptive limit, system rich (Rear Side).
181 Fuel system at part throttle rich adaptive limit, system lean (Rear Side).
182 Fuel system at idle lean adaptive limit, system rich (Rear Side).
183 Fuel system at idle rich adaptive limit, system lean (Rear Side).
184 MAF sensor input voltage is greater than expected, in range.
185 MAF sensor input voltage is less than expected, in range.
186 Closed loop injector pulse width longer than expected.
187 Closed loop injector pulse width shorter than expected.
188 Fuel system at part throttle lean adaptive limit, system rich (Front Side).
189 Fuel system at part throttle rich adaptive limit, system lean (Front Side).
193 Flexible Fuel sensor circuit failure.
211 PIP circuit failure.
212 Loss of tachometer/IDM input.
213 EEC SPOUT circuit open.
214 CID circuit failure.
215 PCM detected coil 1 primary circuit failure.
216 PCM detected coil 2 primary circuit failure.
217 PCM detected coil 3 primary circuit failure.
218 Loss of ignition diagnostic monitor signal-left side.
219 Spark timing defaulted to 10 degrees, spark output circuit open.
221 Spark timing error.
222 Loss of ignition diagnostic monitor signal-right side.
223 Loss of dual plug inhibit control.
224 PCM detected coil 1, 2, 3 or 4 primary circuit failure.
225 Knock not sensed during dynamic response test KOER.
226 Ignition diagnostic monitor signal not received.
232 PCM detected coil 1, 2, 3 or 4 primary circuit failure.
238 PCM detected coil 4 primary circuit failure.
241 Ignition control module to PCM ignition diagnostic monitor pulse width transmission error.
244 Cylinder Identification circuit fault present when cylinder balance test requested.
311 Secondary air injection system inoperative during KOER self-test (bank #1).
312 Secondary air injection system misdirected during KOER self-test.
313 Secondary air injection system not bypassed during KOER self-test.
314 Secondary air injection system inoperative during KOER self-test (bank #2)
326 PFE sensor circuit voltage lower than expected.
327 PFE sensor circuit voltage below Self-Test minimum.
328 Exhaust gas recirculation valve position sensor closed voltage lower than expected.
332 Insufficient EGR flow.
334 Exhaust gas recirculation valve position sensor closed voltage higher than expected.
335 PFE sensor circuit voltage out of Self-Test range.
336 PFE sensor circuit voltage higher than expected.
337 PFE sensor circuit voltage above Self-Test maximum.
338 Engine coolant temperature lower than expected (thermostat test).
339 Engine coolant temperature higher than expected (thermostat test).
341 Octane adjust service pin open.
381 Frequent A/C clutch cycling.
411 Cannot control RPM during KOER low RPM check.
412 Cannot control RPM during KOER high RPM check.
415 Idle Air Control system at maximum adaptive lower limit.
416 Idle Air Control system at upper adaptive learning limit.
452 Insufficient input from VSS.
453 Servo leaking down.
454 Servo leaking.
455 Insufficient RPM increase.
456 Insufficient RPM decrease.
457 Speed control command switch(s) circuit not functioning.
458 Speed control command switch(s) stuck/circuit grounded.
459 Speed control ground circuit open.

Jan 15, 2009 | 2001 Ford Windstar

1 Answer

What does a po1165 code in a 2001 hyundai santa fe mean


P1142 = Load Calculation Cross Check Lower Limit Exceeded

P1165 = Bank 1, Long Term Fuel Trim, Range 1 Rich Limit Exceede

need fix ya rate okay!!

Aug 27, 2008 | Hyundai Santa Fe Cars & Trucks

Not finding what you are looking for?
2003 Audi A4 3.0 Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14223 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...