Question about 2006 Mitsubishi L200 2.5

Open Question

Changing bulbs changing headlight bulb

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: how do i change the headligghts bulbs in a mitsub. galant 2001

the lights a rubber sleeve around them and you have to remove it first to get the bulb unplugged.

Posted on Oct 07, 2008

  • 25 Answers

SOURCE: how do i dismount my headlights to change the bulbs?

You dont have to remove the headlamp to change the bulb, you should have a cover at the rear of the lamp assembly that turns anti-clockwise, the bulb is behind this cover, before you can remove the bulb you have to take the wiring plug off by pressing the tags on the sides of the plastic plug, then the bulb will be held in by a wire spring clip... hope this helps

Posted on Oct 12, 2008

  • 166 Answers

SOURCE: how do I change my headlight bulb

go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Posted on Dec 21, 2008

  • 15 Answers

SOURCE: Need to change headlight bulb

I have a 2003 Galant. There is only 1 bulb for both the high and low beam. When I replaced mine, all I had to do was pull off the rubber cap then pull the bulb out.

Posted on Mar 01, 2009

  • 1 Answer

SOURCE: How to change the headlight bulb on a 2001 mitsubishi galant?

On either side of the headlight wiring assembly, in the engine compartment, you will find 2 small tabs. They are located to the sides and towards the bulb of the plastic assembly. Press these 2 tabs in while pulling the wire assembly out. Remove the rubber gasket and unhook the wire spring holding the bulb in place. The bulb come right out. The bulbs are halogen so do not handle the new bulb by the glass.

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the head light on a 2008 chevy Malibu


Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. Changing both headlight bulbs on your Malibu at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. In some Chevrolets, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb (and vise versa). Some Chevrolets have high intensity discharge headlights, sometimes referred to as xenon lights. These bulbs have a very high voltage that runs through them, even if the battery is disconnected. If your Malibu has this type of bulb, we do not recommend that you attempt to change it yourself.

When you change the headlight on your Malibu, it is important to not touch the glass part of the bulb with your fingers because the oil from your fingertips will cause that part of the bulb to burn hotter, which significantly shortens the life of the bulb.

Hope this helps! :)

Feb 25, 2015 | 2008 Chevrolet Malibu

1 Answer

I need to change the headlights in a 1998 cavalier but I don't know how to take off the cover for the headlights?


You change the bulbs from the back of the composite headlight assembly. Open the hood, turn the bulb connector counterclockwise-about a quarter turn, and pull connector and bulb out. Take old bulb out, put new on on-don't touch the bulb glass with your fingers, body oil may shorten bulb life.

Dec 23, 2012 | Cars & Trucks

1 Answer

How to change the bulb in 1999 RAV-4


Instructions
    • Open the RAV4's hood and locate the headlight bulbs plugging into the rear of the headlight assemblies. Each assembly has two bulbs, one outer and one inner. Unplug the wiring harness from the rear of the burnt-out headlight, by pressing the locking button and pulling down on the harness.
    • 2Grab the rear of the bulb and rotate the bulb about a quarter turn counterclockwise to unlock it. Pull the bulb from the headlight assembly.
      3
    • Grab a new 9005 (high beam) or 9006 (low beam) bulb by its plastic base. Insert the bulb in the rear of the headlight assembly, lining up the tabs on the bulb with the notches in the headlight assembly, and twist it clockwise to lock the bulb in place. Do not touch the glass part of the headlight bulb, as the oils from your hands can cause the bulb to fail prematurely.
    • 4Plug the wiring harness into the receptacle on the rear of the bulb

Jun 27, 2012 | 1999 Toyota RAV4

1 Answer

How to change headlight 2003the x type Jaguar


look inside owners manual in glove compartment look up bulb replacement in the back index it will show and tell you how to replace headlight bulbs. be sure to wear clean gloves, because headlight bulbs or halogen type bulbs, if oil from hands or skin touch the halogen bulb it will cause halogen light bulb overheat and blow out.you can go by auto parts store when you buy new headlight bulb the salesperson will go out to vechicle and replace headlight bulb for you wont charge you any thing.just charge you for the headlight bulb.

Feb 12, 2012 | 2003 Jaguar X-Type

1 Answer

My car 2003 altima I need change light bulb. need know how to remove head light to change the bulb.


You don't have to remove the headlight to change the bulb. The bulb can be removed from the back of the headlight, usually by turning the bezel ring that holds the bulb onto the headlight housing. Just make sure you do not touch the glass part of the bulb while replacing it or it will burn out again fast.

Jan 27, 2011 | 2003 Nissan Altima

1 Answer

Need to replace headlight lens on a 1996 dodge avenger


Usually, one has to get the entire headlight assembly to replace the lens.
Is it cracked?
If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

---
REMOVAL & INSTALLATION

CAUTION
Halogen bulbs contain gas which is under
pressure. Handling the bulbs incorrectly could cause it to shatter into flying
glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
before removal. Handle the bulb only by the base; avoid touching the glass
itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

  • Turn the headlight switch OFF and allow the bulb to cool before
    changing it. Leave the switch OFF until the change is complete.
  • ALWAYS wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • DO NOT drop or scratch the bulb.
  • Keep dirt and moisture away from the bulb.
  • Place the used bulb in the new bulb's package and dispose of it properly.


Cirrus, Stratus, Sebring Convertible and Breeze


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the 2 screws securing the headlight module to the radiator closure
    panel.
  4. Pull out the headlight module from the vehicle.





    Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
    module retaining screws
    90906p69.jpg






    Fig. 2: Pull the headlight module straight out of the front of
    the vehicle to remove the bulbs
    90906p70.jpg






    Fig. 3: Disconnect the wiring harness for the headlight bulb
    90906p74.jpg






    Fig. 4: Turn the light bulb retaining ring counterclockwise,
    and remove it from the back of the module
    90906p75.jpg






    Fig. 5: Pull the light bulb out from behind the module. Never
    touch the glass of the light bulb
    90906p76.jpg



  5. Detach the headlight electrical connector.
  6. Remove the retaining ring holding the bulb to the back of the headlight
    module.
  7. Pull the bulb from the back of the headlight module. Hold the bulb by its
    base only; try not to touch the glass itself.
    To install:

  8. Holding the bulb by the base, place it in the headlight module, then secure
    with the retaining ring.
  9. Attach the electrical connector to the bulb.
  10. Install the headlight module into the vehicle and tighten the 2 retaining
    screws.
  11. Connect the negative battery cable and check the headlight operation.


Sebring Coupe and Avenger


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the sealing cover by rotating it counterclockwise.
  4. Remove the bulb attaching spring and pull out the light bulb.





    Fig. 6: Remove the headlight sealing cover(s)
    90906g28.gif






    Fig. 7: Remove the attaching spring and pull out the bulb
    90906g29.gif

    To install:

  5. Install the bulb into the headlight module.
  6. Install the bulb attaching spring.
  7. Install the sealing cover.
  8. Connect the negative battery cable and check the headlight operation.


prev.gif next.gif

Oct 07, 2010 | 1996 Dodge Avenger

1 Answer

How do I change headlight bulb . Left side low beam headlight bulb is blowed . I have the new bulb and just need to know where the lever or turn object is to remove from the back side so I can change the...


Reach beind the headlight and just unscrew the cap that holds it in. However don't touch the new bulb with your bare fingers or you will drastically shorten the life of the bulb.

Oct 16, 2009 | 2003 Chevrolet TrailBlazer

1 Answer

Change headlight bulb


Removal & Installation Bulb Replacement To Remove:
  1. Release the spring clip and remove the protective cover from the rear of the bulb.
  2. Disconnect the electrical connector from the bulb.
  3. Remove the spring clip and remove the bulb from the headlight housing.
To Install:
CAUTION
Do not touch the glass portion of the new bulb with bare hands.
  1. Insert the bulb in the housing.
  2. Secure the bulb with spring clip.
  3. Connect the electrical connector to the bulb.
  4. Install the protective cover on the headlight assembly.
Headlight Assembly

Jul 16, 2009 | 2004 Volkswagen Jetta

2 Answers

How do you change the right front headlight bulb on a kia sedona


Remove the headlight assembly. Just remove the 3 bolts with a 10 mm socket and pull it out so you can disconect the wire harness. After that pull the whole assembly out and unscrew the bulb cover. The bulb is held in with a spring clip.

Dec 25, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
2006 Mitsubishi L200 2.5 Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...