Question about 2007 Ford Five Hundred Limited Sedan
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
couple things could had appened first the cruise control module or cru may have went out could be a malfuntion in the with some speed sensors or the vaccum lines have gotten to dry rotted to do the job necessary to maintain the speed
Posted on Mar 24, 2009
clock spring in the steering column is my guess. They are delicate and have to do with anything in the steering wheel like airbag, horn, or anything that is operated by buttons on the wheel. These wires have to turn constantly with the steering wheel and the "clock spring" goes bad often enough
Posted on Jul 08, 2009
Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.
It could be a blow fuse in the recall harness, if you did have it done.
Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.
1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.
2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.
If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.
The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.
There will be a slight delay when the last button is pressed and the lamp flashes.
3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.
If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:
— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
Posted on Feb 23, 2010
If the cruise lamp comes on and the cruise does not set i would advise inspecting the cruise cable and make certain it is not broken, if ok the the servo has likely failed.
Posted on May 29, 2010
This is a dangerous defect. What you want to do is isolate the Cruise cable from the Throttle mechanism. Then get the Cruise cable away from the Throttle so it can not jam the Throttle accidentally.
With the engine OFF use your hand and move the remaining Throttle mechanism and feel for sticking or roughness in the control. If you feel binding, start removing the connection of the Throttle cable and work your way through all the moving parts like a Butterfly flap on the Airhorn, the TPS (throttle position sensor) and so on until you find out what is rubbing.
It is possible that the Cruise was disengaging because the Throttle parts were binding. If disconnecting the Cruise eliminates the sticking throttle, then all the problems came from the Cruise control cable or the Cruise Box. Once you have made a thorough check of the Throttle you can blame the Cruise for your problems and replace the parts.
Posted on Jun 22, 2010
Tips for a great answer:
Mar 26, 2016 | 2005 Ford Freestar Wagon
Apr 06, 2014 | 2005 Ford Taurus
-----------Horn and Cruise control quit working?
Horn and cruise control not working on car?
Horn and Cruise control quit working suddenly?
Cruise control stop working ?
ford ranger cruise control not working?
My Cruise control not working?
This troubleshooting help links will help you to confirm the problem.
Feb 13, 2012 | Chevrolet 3500 Cars & Trucks
Feb 07, 2012 | 2005 Ford Ranger
Oct 11, 2011 | 2005 Ford Taurus
May 07, 2011 | 2005 Ford Escape
Mar 18, 2011 | 2005 Ford Five Hundred
Jul 21, 2010 | 2005 Ford Mustang
Jun 30, 2010 | 2001 Ford Escort ZX2
May 17, 2010 | 2005 Ford Taurus
Jul 02, 2014 | 2007 Ford Five Hundred Limited Sedan
142 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: