Question about 2008 Jeep Patriot 2.4

1 Answer

Serpentine belt Can't find tensioner to replace serpentine belt. Where is it

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 41,560 Answers

They look just like an idler pulley .only they have a spring internally that keeps belt tight . go to auto parts store and buy one then look for it when you get ready to change it out

Posted on Jul 12, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: cant figure out how to

go to auto zone . com they have a complete diagram on how to do that !

Posted on Jul 15, 2008

motor1258
  • 6674 Answers

SOURCE: change a serpentine belt on 04 jeep grand cherokee laredo

Check this link & scroll down to your engine. Click on picture to expand.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004328a

Posted on Feb 03, 2009

motor1258
  • 6674 Answers

SOURCE: can't release tension on serpentine belt

You might find tension is adjusted at your power steering pump for that engine & belt.

Posted on Jun 02, 2009

motor1258
  • 6674 Answers

SOURCE: Jeep cherokee country tensioner pulley noise

May be a weak tensioner that needs replacing. Make sure you clean pulleys well with brake cleaner or similar as well. I have had one with similar problem, that Gator back belt was causing it. I'm not 100% convinced that a notched belt will get as good a grip as a complete rib all the way around the belt. Just doesn't add up to me. If you compare that to tire grip, then you'd be telling me that snow tires would work better on the Nascar circuit?

Posted on Jun 28, 2009

  • 6982 Answers

SOURCE: how do i replace serpentine belt on 1997 jeep wrangler

Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.

Posted on Aug 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt


Application:
With A/C


2.image

Kia_Sedona_2002-2006
Accessory Drive Belts

Print


Accessory Belt Routing



0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt (A) routing-3.8L engine


Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:
  1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
  2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
  3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.

    0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt routing-3.5L engine


    0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt (A) routing-3.8L engine


May 09, 2012 | 2006 Kia Sedona 3.8

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    2 Answers

    Change serpentine belt on 06 sienna


    1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
    2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
    3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
    4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
    5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
    6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
    7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
    8. 8 Remove the wrench and close the hood.
    Thank you and good luck,
    Lee

    Aug 26, 2010 | 2006 Toyota Sienna

    1 Answer

    How do i release the tension belt ... cant seem to find bolt being referred to in other docs


    Here's the procedure on how to release and replace the tension belt of your car.

    Step 1
  • Open the hood on the Volvo S-60 and find the serpentine-belt routing diagram. The diagram should be attached to the top of the fan shroud that covers the radiator. If not, draw out the exact routing method of the serpentine belt around each pulley with a pen and a piece of paper.
  • Step 2 Locate the serpentine-belt tensioner that is in the very center of the engine. The tensioner will have a square bolt head in the center of the tensioner pulley.
  • Step 3 Slide the open end of the 5/8-wrench onto the square bolt head in the center of the belt-tensioner pulley. Turn the tensioner pulley counterclockwise and slide the serpentine belt off of the tensioner pulley.
  • Step 4 Remove the serpentine belt from the other pulleys and pull the belt out of the engine compartment.
  • Step 5 Slide the new serpentine belt into the engine compartment and around the crankshaft pulley.
  • Step 6 Route the new serpentine belt around each pulley. Turn the belt-tensioner pulley counterclockwise again and slide the serpentine belt around the tensioner pulley. Release the tensioner and it will tighten the belt around the pulleys. Look over the belt to ensure that it is inside of each pulley.
  • Step 7 Crank the S-60 and look over the serpentine belt with the motor running. Let the engine run for about one minute and shut the engine off. Close the hood.
  • Aug 12, 2010 | 2001 Volvo S60

    1 Answer

    Replace serpentine belt on 1992 dodge grand


    Click on the following free direct Link.
    It has the correct Belt Diagrams for your 1992 Dodge Grand Caravan wirh either the 3.0L SOHC V6 or the 3.3L V6.

    http://www.2carpros.com/car_repair_information/year/1992/make/dodge/model/grand_caravan/1992_dodge_grand_caravan_drive_belt_routing_diagram.htm


    Included on the Diagrams are the Instructions on "Rotating" the Automatic Tensioner. See Below for additional Instructions to make your job easier.

    "HOW TO": I professionally prefer the Serpentine Tensioner Tool.
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s).
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening located on the Tensioner Arm) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


    Before You GO:
    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

    Apr 11, 2010 | 1992 Dodge Grand Caravan

    1 Answer

    How to remove and replace a serpentine belt 96 saturn


    Click on the following free, direct Link. It has all the Serpentine Belt Diagrams you will need for the 1.9L 4-Cylinder Engine and various Engine Options (AC/No AC etc.), complete with Instructional and Directional Diagrams.

    http://www.2carpros.com/car_repair_information/year/1996/make/saturn/model/sl/1996_saturn_sl_drive_belt_routing_diagram.htm

    Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

    "HOW TO":
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s). (See Diagrams on Link)
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

    Apr 04, 2010 | 1996 Saturn SL

    1 Answer

    Tension pulley for serpentine belt making noise


    The Tensioner Pulley Bearings are failing and either the Tensioner Pulley or the Tensioner Assembly (Pulley, Arm and Base) must be removed and replaced.

    Click on the following free direct Link. It has several of the Serpentine Belt Diagrams and Tensioners that are possible with your 4.3L V6 engine.
    http://www.2carpros.com/car_repair_information/year/1998/make/gmc/model/jimmy/1998_gmc_jimmy_drive_belt_routing_diagram.htm
    1. Remove the Serpentine Belt.
    "HOW TO":
    Standard Rules to Removal the Serpentine Belt with a Tensioner:
    A. Find the Tensioner(s). (See Diagrams on Link)
    B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    C. Remove the loosened belt off one of the other more easily accessed Pulleys.
    D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Removing the Tensioner Pulley: See the Diagrams in the Link.
    After the Belt has been removed, with the Tensioner resting:
    DEPENDING ON WHAT TYPE TENSIONER:
    IF the Tensioner Pulley itself HAS a Bolt Head showing, SOME of these bolts can be removed and the Tensioner Pulley replaced.
    IF the Tensioner Pulley itself DOES NOT HAVE a Bolt Head showing, then go to the Tensioner Base located at the end of the Tensioner Arm. This should have a Bolt Head Showing. Remove this Bolt and the whole Tensioner Assembly will com off.

    When replacing the Tensioner Assembly - MAKE SURE you place the protruding "nipple" on the underside base of the Tesnioner into the appropriate cavity on the engine face.

    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Mar 29, 2010 | 1998 GMC Jimmy

    1 Answer

    Replacing serpentine belt


    Click on the following direct Link. It has the Serpentine Belt Diagram that you will need depending on your engine size (2.0L or 3.0L) and your options (AC/No AC ect.).
    http://www.2carpros.com/car_repair_information/year/2001/make/mazda/model/tribute/2001_mazda_tribute_drive_belt_routing_diagram.htm

    Standard Rules to Removal the Serpentine Belt with a Tensioner:
    1. Find the Tensioner(s). (See Diagrams on Link)
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.


    Standard Rules for Installing the Serpentine Belt with Tensioners:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

    Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

    Mar 23, 2010 | 2001 Mazda Tribute

    5 Answers

    Serpentine belt replacement


    2.0L Engines
    See Figures 11, 12 and 13
    The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner.
    Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension.
    The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced.
    0900c1528008d836.jpgFig. 11: Drive belt routing-2.0L SOHC engine with A/C 0900c1528008d837.jpgFig. 12: Drive belt routing-2.0L SOHC engine without A/C 0900c1528008d838.jpgFig. 13: Drive belt routing-2.0L DOHC engine

    Jul 24, 2008 | 1999 Ford Escort

    Not finding what you are looking for?
    2008 Jeep Patriot 2.4 Logo

    Related Topics:

    90 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7782 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...