Question about 2008 Jaguar Xf Sedan

Open Question

Tire pressure monitor system reset jaguar xj - 2008 Jaguar Xf Sedan

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: installing a/c hose (evap to drier) 1997 jaguar xj-6

with great difficulty,tell me about it ------undo radiator mounts and jiggle it over a bit ,the support brackets on mine were pop rivited to chassis .remove the top bar that goes over the top of the rad first though.

Posted on Feb 13, 2009

Ad
  • 1 Answer

SOURCE: 1996 jaguar xj 6 fuel reset button

Press down on the inertia switch. Located up and
to the left of the brake pedal.

Posted on Jun 06, 2009

  • 2 Answers

SOURCE: left rear wheel/tire tilts inward

Jack that wheel position up , and shake the wheel vertically , and see if there is excesive wheel bearing play .

Posted on Aug 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the check tire pressure indicator


Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .
  1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
  2. Turn ON the ignition, with the engine OFF.
  3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
  4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
  5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

Oct 08, 2015 | 2006 Pontiac Grand Prix

1 Answer

Why does tire light stay on 2011 Toyota?


Reset the Tire pressure monitoring system light. The reset button is located under the steering side under the finish panel. You have to bend down to see the button.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON

Jul 23, 2014 | 2011 Toyota Highlander

1 Answer

Tire monitor


To troubleshoot the issue,go through the help link mentioned below:---
CARS: Working of
tire pressure monitoring system
http://technoanswers.blogspot.in/2012/10/cars-working-of-tire-pressure.html-------------
GMC ENVOY spare tire system stopped working?
http://repairhelpcenter.blogspot.com/2012/01/gmc-envoy-spare-tire-system-stopped.html

TIRE PRESSURE LIGHT COMING ON?
http://whoisbyme.blogspot.in/2012/07/tire-pressure-light-coming-on.html

What is Best Tire For the Vehicle?http://technoanswers.blogspot.in/2012/04/what-is-best-tire-for-vehicle.html------------
1998
Toyota
Camry: Tires Make Knock Rattling Noise Over Bumps?http://whatisbyme.blogspot.in/2012/05/1998-toyota-camry-tires-make-knock.html

These will help. Thanks.

Dec 17, 2012 | 2001 Oldsmobile Alero

3 Answers

My low tire light came on so I went and had air and all the tires checked but now I don't know how to turn the light off. I have had the car since 2000 and it has 50,000 miles on it but could never figure...


Hello Mattingly.

Here is some information for you regarding your problem.

The Tire Inflation Monitor (TIM) system alerts the driver when the pressure changes in one of the tires. The system only detects a low pressure condition while the vehicle is being driven. Once a low tire pressure condition is detected, the system informs the driver that a low tire pressure condition exist's, whenever the ignition is ON.
The LOW TIRE message appears on the Instrument panel if the tire pressure in one tire becomes at least 82 kPa (12 psi) lower or higher than the other three tires. The message does not appear if more than one tire is low or high, or if the system is not calibrated properly. The system does not inform the driver which tire is low. To clear this message, set the tire pressures in all four tires to the proper pressures and perform the system reset procedure. Refer to Tire Inflation Monitor Reset Procedure for service procedure.
The Tire Inflation Monitor software requires approximately one half hour of straight line driving to complete the TIM autolearn. There are several speed ranges that the EBCM needs to learn the tire inflation configuration in order to have the full capability of detecting a low tire condition. The speed detection ranges are the following:

  • 24-64 km/h (15-40 mph)
  • 64-113 km/h (40-70 mph)
  • 113-145 km/h (70-90 mph)
Each speed range has 2 modes of low tire detection.

  • Monitor Mode 1
  • Monitor Mode 2 The EBCM learns the tire inflation configuration for each speed range independently. In Monitor Mode 1, the EBCM has only partially learned the tire inflation configuration for the speed range and has limited detection capability for a low tire condition. In Monitor Mode 2, the EBCM has fully learned the tire inflation configuration for the speed range and has full detection capability for a low tire condition. If the EBCM is not in Monitor Mode 1 or Monitor Mode 2, a low tire condition cannot be detected because the EBCM has not learned the tire inflation configuration of the vehicle.

To reset (calibrate) the system:
Turn the ignition switch to RUN. Then press and hold the RESET button for about five seconds. The red RESET button is located inside the instrument panel fuse block on the right side of the dash.. The LOW TIRE light will come on and flash three times and then it will turn off.
The system completes the calibration process during driving.
The system normally takes 15 to 20 minutes of driving in each of three speed ranges to "learn" tire pressures. The speed rages are 15 to 40 mph (25 to 65 km/h), 40 to 65 mph (65 to 105 km/h) and above 65 mph (105 km/h).

There you are, this should fix you up.
Keep in mind this system uses wheel speed sensors to calculate. If one of your sensors isn't working your low tire light will remain on.

Thank you for using FixYa.

KL

Jan 20, 2011 | 2000 Buick Century

3 Answers

Reset tire pressure monitoring system


after you have inflated the tires to the correct pressure press the tire pressure button for a few seconds untill you hear a beep sound .that indicates the tire pressure has been reset. hope that helps

Dec 22, 2009 | 2009 Volkswagen Tiguan

1 Answer

Tire warning light will not go out


Check the spare tire pressure and make sure it's 32 PSI.

Fix-A-Flat emergency air can will destroy the first generation sensor.

Tire shop will has Tire-pressure monitoring system (TPMS) reset hand held unit to reset the monitoring system.

Dec 11, 2009 | 2008 Mazda MAZDA6

2 Answers

How do I reset the low tire warning light?


TIRE PRESSURE MONITOR RESET PROCEDURE

IMPORTANT: There are 3 different ways to reset the Tire Pressure Monitor (TPM) system. After resetting, the TPM system requires up to 30 minutes of straight line driving in each of the 3 speed ranges to complete the calibration process.If the TPM system does not reset, or DTC C1245 remains current, refer to Diagnostic System Check - Tire Pressure Monitoring. For further information, refer to Tire Pressure Monitor Description and Operation.

USING THE EXTERIOR LAMP SWITCH
  1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
  2. Turn "ON" the ignition, with the engine OFF.
  3. Cycle the exterior lamp switch from "OFF" to parking lamps 3 times within 5 seconds.
  4. Use the scan tool in order to clear the TPM DTC.
USING THE RDS RADIO, IF EQUIPPED
  1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
  2. Turn the ignition to "ACC" or "ON", with the engine OFF.
  3. Turn the radio "OFF".
  4. Press and hold the "DISP" button until "SETTINGS" is displayed.
  5. Press the "SEEK" up or down arrows until "TIRE MON" is displayed.
  6. Press the "PREV" or "NEXT" button to enter the submenu. "RESET" will be displayed.
  7. Press the "DISP" button, A chime will sound and "DONE" will be displayed.
  8. Scroll until "EXIT" is displayed.
  9. Press the "DISP" button to exit the TPM reset mode. A chime will sound to verify exit.
  10. Use the scan tool in order to clear the TPM DTC

Oct 11, 2009 | 2003 Chevrolet Impala

3 Answers

Where is the low tire reset button located on 2005 ford freestar?


It is on the same button as the Trip Odometer. Cycle through until you see Tire Reset and hold the button down.

Mar 28, 2009 | 2005 Ford Freestar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...