Question about 1994 Ford Ranger Supercab

1 Answer

Where is the egr valve located on a 1994 ford ranger

The check engine light comes on at start up

Posted by on

  • Lloyd Gardinerjr Apr 22, 2014

    when the light come on some time it is telling that you need service if you do not need any service then your computer need to check get a OD METER and you can turn off the engine light your proplem is not bad that is normal some for the light to come on when your vehicle need service

  • Lloyd Gardinerjr Apr 22, 2014

    the egr valve is on the top of the engine it is round you can find it on ebay cheap just type in the word and it will bring it up with the price

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Should be on the back driver side of the motor

Posted on Apr 21, 2014

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14 Answers

SOURCE: egr valve insufficient flow detected

You probably pulled a code p0401, insufficient egr flow. Your DPFE sensor is more than likely at fault. There has been a lot of trouble with these sensors. Then reset CEL or disconnect battery for 5 minutes.

Posted on Aug 17, 2008

  • 1114 Answers

SOURCE: Would faulty EGR valve cause check engine light to come on?

If EGR was out your engine light would stay on!usually hi way drive is a whole new emission game sensor work 100% different that city drive you have a O2 sensor problem don"t Get$$ the problem when if you say it only will do it on highway then take it on highway with OBD 2 in run scan mode have a passenger observe it this will give the the proper code you will need to peg it cheers!

Posted on Dec 27, 2008

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

  • 61 Answers

SOURCE: I changed EGR valves, selinoid, sensors, and even

go to auto zone or someone with a scan tool to find out what codes are stored on the computer in the car

Posted on Jul 30, 2009

  • 8 Answers

SOURCE: Need a pic veiw of 2004 ford f350 6.0L diesel EGR

1st of all when Ford started out with putting "EGR's" on those diesel engines, they rushed it and are nothing less than a pain in the ***! i recommend having an EGR cleaning service performed by your local Ford dealer, i know they charge up the wazoo, but they're the best people to perform the service period.this is a VERY common problem with those engines and that service is "supposed" to be performed every 30K I believe. i dont recommend attempting to remove and service it youself, this WILL only make it worse.

Posted on Mar 26, 2010

Testimonial: "Im relieved to here that someone else is thinking the same thing. Im still going to try it myself as i am somewhat skilled at this but Thanks a bunch!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Either code 4000 or 1400 on 2002 ford ranger 4.0 ltr v6. the right code should equate to the egr valve. I have replaced the egr valve but check engine light comes on again after reset showing same code.


code p1400 is a DPF EGR sensor CIRCUIT LOW VOLTAGE detected. most likely is a problem with the wiring to the egr or dpfe sensor. the pinpoint tests for code p1400 instruct you to test all wiring before replaceing the egr or dpfe sensor

Jan 19, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

Where is the egr valve located on a 1994 Ranger 4.0L V6?


If your ranger has a egr valve it will be on the driver's side of the upper intake plenum (the top aluminum housing, very top of the motor) and about centered on the plenum.in 1994 I have seen Rangers with and without a egr valve. I believe it depends on if its California emissions or not.

Dec 31, 2010 | Ford Ranger Cars & Trucks

1 Answer

My 1994 ford ranger ... the starter cranks.. but if the check engine light does not come on... it doesnt start... when the light comes on.. it starts... Intermittent... what do I check ??


Had the same problem and it's so simple a fix. It's the Fuel Relay Fuse located in the fusebox in the engine compartment on the driver side. Take It costs like $13 and is the same as the AC relay. Next time it happens pop the AC fuse in it's place.

Aug 05, 2010 | 1994 Ford Ranger Supercab

1 Answer

Ford 1994 Explorer. After 20-30 minutes of


yes the egr could be clogged or loosing vaccum check the valve by taking it out or looking to see if the pickup tube on the valve is bad or has a pin hole in it.

Jul 01, 2010 | 1994 Ford Explorer Limited

2 Answers

Ford Ranger check engine light. I had it diagnosed as an EGR Valve, replaced it and the light cam back on after about 5 miles.


They all say the EGR valve is the problem but most of the time its the mass air fow meter is at fault.So i would recomend changing that.

Dec 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Egr valve on ford 98 ranger, ck. eng. light on


disconnect it and seal it off with a piece of broom handle in the inlet side.sounds drastic i know but it works.

Mar 04, 2009 | 1998 Ford Ranger SuperCab

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...