Question about Cars & Trucks

1 Answer

How to fine Inertia switch in a 2000 Mazda 626

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Cars & Trucks Expert
  • 176 Answers

For how long i know only ford had it

Posted on Apr 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: 2000 mazda 626 check engine light went on . code

probley not egr valve it probley egr control solenoid or wiring

Posted on Apr 11, 2010

SOURCE: Mazda 626

Hi Janieanip01,
Again we need more imfo....Is the vehicle injection?....If it is you'll have to wait until the fuel rail is re-pressurised before it will start....Crank it for about ten seconds at a time so as not to burn out the starter motor....It may be that the vehicle didn't run out of fuel but instead the pump may have given in....and when did you last replace the fuel fiter?
Regards Johngee10

Posted on Aug 10, 2008

CRTN
  • 716 Answers

SOURCE: changing the tail light bulbs on a 2000 mazda 626

The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.

Posted on Jan 26, 2009

alicantecoli
  • 22219 Answers

SOURCE: looking for the location of crank shaft on 2000 mazda 626

i assume you mean crank shaft sensor ,if its not on the front puilley then look around the bell housing in the most extreme awkard in accessable position possible because you can bet that is where it is

Posted on Jun 14, 2010

SOURCE: Mazda 626 2000 Need

The is no Fuel Inertia Switch --Only on Ford Products

Posted on Jul 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the inertia switch located on a mazda 626, 2002


Only Ford products use an inertia switch for the fuel pump.
Mazda only uses a relay controlled by the engine computer.

Oct 21, 2015 | Mazda Cars & Trucks

1 Answer

Where is the inertia switch located on a 2000 626 Mazda


You Mazda does not have an inertia switch like the fords do. The only things that control the fuel pump are the pcm, fuel pump relay, and the fuel pump fuse.

May 25, 2015 | 2000 Mazda 626

1 Answer

Need location of tipped inertia switch on 2000 mazda 626


To the best of my memory it doesn't have one the computer shuts the fuel off its probably a relay out or bad pump being that old good chance it is the pump

Jan 03, 2015 | Cars & Trucks

1 Answer

Where is the inertia switch on a 2000 mazda 626


It is under the dash near the heater box by the transmission. Hump

Jan 03, 2015 | Cars & Trucks

1 Answer

I have no power going to the fuel pump


one thing to check is the inertia switch. it kills power to the fuel pump in case of an accident, or sometimes a large pothole. it can be reset once you locate it.

Aug 31, 2014 | 2000 Mazda 626

1 Answer

Where is inertia switch in 94 Mazda 626 2.0


No inertia switch. That was a common problem on these cars., The alarm box gave problems and it is what is causing the fuel pump to shut off. Good luck finding one. The easiest and cheapest way to fix is to give it ignition power when you turn ignition on. If you want to be a bit safer, buy a ford KA inertia switch, secure it at the l/f kick panel directly onto the body (It works with shock waves) to cut of fuel in case of an accident Luckily you don't have to take the tank out, you just remove the rear seat and the metallic cover. .

Jul 27, 2014 | 1994 Mazda 626

1 Answer

Is there a reset button for a fuel pump 94 Mazda 626


Here you go, it should be to the left of your left foot wile sitting in the driver's seat under a panel.

Jul 23, 2014 | 1994 Mazda 626

1 Answer

Location of inertia switch


If it has an inertia switch, it will be on the passenger side under the kick panel under the glove box.

Apr 20, 2014 | 2000 Mazda 626

1 Answer

Mazda 626 2000 Need to know where the reset or inertia switch is


The is no Fuel Inertia Switch --Only on Ford Products

Jul 12, 2011 | 1995 Mazda 626

1 Answer

Is there a reset button for a fuel pump 95 mazda 626


no there is not a reset button or fuel inertia switch for this vehicle.

Mar 31, 2011 | 1995 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...