Question about 2006 Saab 9-3 2.0T

1 Answer

EPS Light is on

I changed the front Wheels Bearing/Hub and now the EPS Indicator is on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saab Master
  • 3,904 Answers

Well. I don't think they will be related. EPS is your electric power steering light. The hub would have the ABS system attached to it. Have it hooked up to a computer at a parts store for free and they will tell you the code that is tripping the light and what it is.

Posted on Apr 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

ESP& ABS indicator light is in


I would be rechecking the rotor position and sensor position on the hub you were working on . check for disconnected wiring or rotor to sensor clearance for the ABS system.

Apr 20, 2014 | 2006 Saab 9-3

1 Answer

Anti lock indicator light has been on for a while, now the brake indicator light comes on while driving and it dings until you kill the ignition?


Check your front wheel speed sensors there may be a broken wire at front wheels brake sensors. If you take it to mechanic shop and they hook up diagnostics, they will get the code for wheel bearing (hub). But the real problem nine out ten is the WIRE going to the sensor.

Sep 06, 2012 | 2003 Pontiac Aztek

1 Answer

Is there any special tools required to change front wheel bearing on 2003 mini


you will need a big socket to remove the axle nut--about 20 mm or so. Other than that, I don't think so. Procedures from autozone.com below. it doesn't mention having to press bearing into hub.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheels Hub nut Brake caliper Rotor ABS sensor Wheel hub from steering knuckle and driveshaft Wheel bearings
To install:
  1. Install or connect the following:

    Wheel bearing into hub Wheel hub to steering knuckle and driveshaft; torque bolts to 41 ft. lbs. (56 Nm) ABS sensor; torque to 6 ft. lbs. (8 Nm) Brake rotor and caliper New flanged hub nut; torque to 134 ft. lbs. (182 Nm)

Oct 05, 2010 | 2003 Mini Cooper

2 Answers

I would like to know if the wheel bearing is in the shaft or the hub?


The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Jun 16, 2010 | 1999 Daewoo Nubira

1 Answer

Replace front wheel bearing on 1998 saturn


The easiest way is to buy the knuckle and front hub together. It is more expensive but unless you have access to a press to press the knuckle from the hub and then press a new bearing in it will be impossible to replace.

Also like any wheel bearing job, change in pairs not just one. So change both front wheels because if one is going then the other is not far behind.

Jun 12, 2010 | 1998 Saturn SL

1 Answer

I need to replace the right front wheel bearing on a 96 saturn sc1 any advice


The easiest way is to buy the knuckle and front hub together. It is more expensive but unless you have access to a press to press the knuckle from the hub and then press a new bearing in it will be impossible to replace.

Also like any wheel bearing job, change in pairs not just one. So change both front wheels because if one is going then the other is not far behind.

Good luck!

Mar 12, 2010 | 1996 Saturn SC

1 Answer

Front hub bearing changed now traction keeps coming on.


It seems that either the bearing is not properly fitted leading to false alarm being generated(maybe the bearings are too tight) such that the brake pads are not equidistant compared to the other side wheel. Well the thumb rule is to replace both since they are the front wheels. Try refitting the bearing but my instinct tells me to change the other wheels bearing too and get the brakes reset with the help of computer guided sensor settings checking & adjustments as required. This will definitely help but don't forget to recalibrate the sensors with the help of a PC at the service station. Its IMP......sodeep

Jul 30, 2009 | 2005 Hummer H2

2 Answers

Oscilating humming coming from left front wheel


SOUNDS LIKE YOU HAVE BAD LF WHEEL BEARING..JACK UP FRONT OF VEHICLE..BLOCK REAR WHEELS..PUT TRANSFER CASE IN NEUTRAL,SPIN EACH FRONT WHEEL BY HAND WITH OTHER HAND ON COIL SPRING..YOU SHOULD FEEL ROUGHNESS IN SPRING ON SIDE THAT HAS BAD BEARING..IT IS A HUB/BEARING ASSEMBLY

Jul 23, 2009 | 2002 Jeep Grand Cherokee

2 Answers

1996 Jaguar XJ6 - seeking toque spec for front hub bearing?


They are taper roller bearings, when new something like 8 or 10 pound feet, used ones tigten until only a little play exists (if you have steel wheels leave the wheel on and it is easy to feel the play even if packed with fresh grease) If you overtighten they will growl and overheat and fail

May 23, 2009 | 1996 Jaguar Xj Series

Not finding what you are looking for?
2006 Saab 9-3 2.0T Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...