Question about 1989 Toyota Pickup SR5

3 Answers

89 4x4 pu broken wheel stud

Son was changing flat. broke stud on drivers rear. do i just pound out the old stud and pound in the new?

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

Will have to remove LR drum, The stud should drive out fairly easily, as a precaution, apply penetrating oil and let soak prior to driving it out. Install the new stud..about a $4 item, (compared to $100 to get one fixed at the toyota store, then put your wheel back on, snug up all lugs then torque to 83 ft/lbs.

Posted on Jun 19, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 3,433 Answers

Basicly yes. drive the oild stud out, but, pull the new stud in with stacked washers and a lug nut put on so flat is against washer. Lubricate stud where it ggoing into axle and the washers and lug nut threads. - good luck - Ned

Posted on Jun 19, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 6,982 Answers

Half right...pound out, use a stack of washers and put nut on backwards and draw stud in. Oil on washers and stud threads helps.

Posted on Jun 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change weel stud rear on 2000 linccom navgater


You need to get experienced help because it involves the rear brakes. You should ask yourself why the stud broke in the first place. The most likely scenario is excessive tightening of the wheel nut. Only use the factory toolkit wrench if you have no option. Otherwise use a torque wrench and never an air gun, they max at 200 ft pounds and most nuts are in the 40-75 pounds region. Check the manual for the figure. The actual job is straight forward enough but needs experience or training.

Jul 05, 2015 | Cars & Trucks

1 Answer

How to replace rear lugs


I'm guessing you mean the wheel studs.The studs are pressed in from the back.Most of the time,you can pound out the old studs with a large hammer,and rotate the axle to find a position to slip out the old one/put in the new one.When buying the new studs,see if you can also buy one plain lug nut(with a flat end).Grease the flat side,and use it to pull the new stud into place.(make sure the shoulder of the bolt makes full contact with the axle flange)

Mar 17, 2012 | 1991 Nissan Pickup

1 Answer

Need to remove rear axle to replace tire studs


You don't need to remove the axle. Remove the rotor or drum. pound out the broken studs with a hammer. Install the new stud into the hole. Use a wheel nut and some washers to pull the new stud into place. They also make a stud installer tool which makes it a little easier.

Dec 02, 2010 | Ford Expedition Cars & Trucks

1 Answer

I am wanting to replace the rear wheel studs that are broken. The wheel hub flange won't come off. Is there a special puller for this, do I need to apply more force or is there another method for removal?


You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Studs for rear wheel mounting broken off. How are they repleced?


First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

How to replace rear wheel stud. 2003 dodge caravan


Should be a pressed in wheel stud, remove hub and have old one pressed out or you can do it the primitive way, by double nutting the old stud and striking it with a hammer to pound it out, if threads are bad then just strike the stud by itself , then replace new stud in opposite fashion...

Sep 15, 2009 | 2003 Dodge Caravan

1 Answer

My rear wheel studs broke off when i was changing a tire and i want to know how i can replace them.


Knock out the old ones with a hammer. Pull new ones in with a couple of washers and a lug nut with the flat side towards hub.

Jun 16, 2009 | 1988 Toyota Celica Liftback

2 Answers

Removal of broken wheel studs on 2004 saturn ion


line up the hole with the stud and beat it out with a 3or4 pound ball peen hammer.

Jun 16, 2009 | 2004 Saturn ION

1 Answer

Broken wheel stud


1. get new studs and nuts
2.remove wheel
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.

May 17, 2009 | 2002 Nissan Sentra

1 Answer

Broken wheel stud.


Studs are pressed in. Heat the studs with a propane torch, and then use a ballpein hammer to pound them out. Insert new studs, and use nuts to draw them into place

May 11, 2009 | 1996 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...