Question about 1999 Ford Mondeo

1 Answer

Hoses wornout water hoses are wornout

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 45,347 Answers

Replace all hoses as they will burst and overheat the engine .

Posted on Apr 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a rattling sound front of engine 4.6 Ford Mustang some say it cud b a water pump or one of the pullers or power steering pump pully


Dear Bruce,
You might use a "mechanic's stethoscope" to check this out.
The first suspicion for you should be a dry/wornout fan belt.
Belts that are dried out and hard can cause this very sound.
Next, take a really long screwdriver ( about 24 inches or more ) and with the engine running at an idle, put the tip on various places ( not the fan belt) where you think the sound seems to be coming from. Then put your ear to the handle and listen to each component.
If you have a bad pulley, or alternator, or water pump, or idler pulley, it will "scream" when you hit the right defective part.
God bless your efforts.

Feb 01, 2017 | Ford Cars & Trucks

1 Answer

1998 Dodge Durango heater hose


The metal section is part of the water pump. You can just replace the rubber section of hose.

Nov 01, 2011 | Cars & Trucks

1 Answer

Overheating when pulling a trailer


may be the water level is low or the piston rings or head are wornout .check the motor oil level too

Jun 13, 2011 | 1995 Ford F350

1 Answer

Cross bearing wornout my nissan caravan


Nothing has to be done at the dealer,unless you like to spend more money..
What part are you referring to?
Do you not have a shop that you regularly take your vehicles to?

May 03, 2010 | 1997 Nissan Maxima

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

Dashboard overheat warning light blinks continuously after 5-mi


It is not the thermostat since it only overheat on stop n go situation. Most likely cause is a bad radiator fan. Turn on the AC and see if both the radiator, and the condenser fan works. They should both be working when the AC is turned on. Lets stick to this for now. Let me know what happened. I don't want to confuse you with too many possiblity.

Nov 14, 2009 | 1998 Volkswagen Jetta

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

2 Answers

I have a noisy timing chain on my explorer


Have it changed, it is already wornout. I'm sure that will
eliminate the noise after the it is replaced.

Sep 24, 2009 | 1998 Ford Explorer

1 Answer

My drivers side window leaks when high pressure water hits the corner neat the side mirror....WHAT TO DO?????????????


the rubber gasket surrounding the unit must be wornout replace it or if minour tear stick it with jel glue for rubber.

Sep 22, 2009 | Nissan 350Z Cars & Trucks

2 Answers

I have a 1997 Citi Chico white. Boot leak!


I had the same problem with my 1999 model. Check under the spare wheel, there are 3 or 4 round metal pieces welded on, but 1 wasn't welded property.

Sep 08, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
1999 Ford Mondeo Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...