Question about 2001 Volkswagen Golf

1 Answer

Golf no spark

No spark on plugs. There is power going to the coil. My dad says it could be the engine control module< but I cant find it

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Think we need an engine code for this one. You will find it in your service book, 3 letters. Also on sticker in boot and on timing belt cover.

Posted on Aug 09, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: No spark at coil

check and clean the points if it has them. under the rotor in the cap

Posted on Jun 03, 2009

  • 176 Answers

SOURCE: No spark Power to coil New wires and new coil

Usually the ignition controll module or pickup coil. Your local auto parts store should be able to test the module for you.

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error Code P0351 for a 2005 Toyota Avalon


Possible causes
Faulty Ignition Coil 1
Ignition Coil 1 harness is open or shorted
Ignition Coil 1 circuit poor electrical connection
Faulty Engine Control Module (ECM)

What does this mean? When is the code detected? Each ignition circuit is continuously monitored by the Engine Control Module (ECM). The test fails when the ECM does not receive a valid pulse signal from the ignition coil. Possible symptoms Engine Light ON (or Service Engine Soon Warning Light) Lack/Loss of Power Engine may be harder to start Engine hesitation Rough engine idle P0351 TOYOTA Description: The ignition system on the vehicle uses individual ignition coils for each cylinder. The Engine Control Module (ECM) controls each ignition coil operation. The ECM sends a ON/OFF signal to energize the ignition coil to create a spark at the spark plug when a spark is required at the cylinder.

May 29, 2017 | Toyota Cars & Trucks

1 Answer

Have a 1986 chevy celebrity tec4 an have no fire from coil ive replaced coil checked fuses an have power going to coil still no fire


ignition will trigger if signal from crank sensor, with hei spark plug tester ,read to coil wire and spark plugs wire if spark , depends wich engine
if c3i coil and module the module could be the problems you can check it before replace
hope it helps

Mar 29, 2014 | 1986 Chevrolet Celebrity

1 Answer

1989 VW Golf wont's start. Coil loses power, no spark


You are describing a bad ignition switch. These fail in such a way that the voltage to the ignition fails while in the crank position.

Apr 25, 2017 | 2000 Volkswagen Golf

1 Answer

My 92 explorer has no spark


Hi, here are some tests you can do to diagnose the problem. Please let me know if you have questions.

First, use a voltmeter or 12 volt test light to check for power on the red wire going to pin 8 of the ignition control module when the key is on. The module is in the left front corner of the engine compartment.

jturcotte_2441.gif
jturcotte_2440.gif

If there is no power, the problem is the ignition switch or EEC relay. If there is power, next, check the ignition coil as listed below.

IGNITION COIL TESTINGPrimary and Secondary Circuit Tests
  1. Turn the ignition switch OFF , disconnect the battery, then detach the wiring harness connector from the ignition coil to be tested.
  2. Check for dirt, corrosion or damage on the terminals.

PRIMARY RESISTANCE
  1. Use an ohmmeter to measure the resistance between the following terminals on the ignition coil, and note the resistance:

Except 2.3L, 2.5L and 5.0L engines


B+ to Coil 1 B+ to Coil 2 B+ to Coil 3
The resistance between all of these terminals should have been between 0.3-1.0 ohms. If the resistance was more or less than this value, the coil should be replaced with a new one.

SECONDARY RESISTANCE


jturcotte_2439.gif

Fig. Fig. 1: Engine ignition coil harness connections-3.0L and 4.0L engines

  1. Measure, using the ohmmeter, and note the resistance between each corresponding coil terminal and the two spark plug wire towers on the ignition coil. The coil terminals and plug wires towers are grouped as follows:
Except 2.3L, 2.5L and 5.0L engines

Terminal 3 (coil 1)-spark plugs 1 and 5 Terminal 2 (coil 3)-spark plugs 2 and 6 Terminal 1 (coil 2)-spark plugs 3 and 4

If the coils test good, move on the the crankshaft sensor.
Using a DVOM set to the DC scale to monitor less than 5 volts, measure the voltage between the sensor Cylinder Identification (CID) terminal and ground by backprobing the sensor connector. If the connector cannot be backprobed, fabricate or purchase a test harness. The sensor is okay if the voltage reading varies more than 0.1 volt with the engine running at varying RPM. (check both the blue and gray wires at the ignition module with the engine cranking.)



jturcotte_2442.gif

Fig. Fig. 3: CKP sensor wire harness connections for the 4.0L (VIN X and E) engines


If there is power and both the coils and sensor check good, replace the ignition control module.

Oct 27, 2011 | Cars & Trucks

1 Answer

How do you remove the ignition coil


Each ignition control module (ICM) has the following circuits:
An ignition 1 voltage circuit A chassis ground An ignition control circuit for each cylinder A low reference circuit
The PCM controls spark by pulsing the ignition control circuits to the ICM to trigger the coils and fire the spark plugs. The PCM and ICM are internally protected against shorts to power and ground on the ignition control circuits.

The spark plugs are connected to each coil by a short boot. The boot contains a spring that conducts the spark energy from the coil to the spark plug. The spark plugs are tipped with platinum for long wear and higher efficiency.


Ignition Control Module (ICM) Connectors

248af41.jpg

Fig. Ignition coil locations 2001-2004 4.8L, 5.3L, 6.0L Engines



Removal & Installation
2.2L (L61) Engine
  1. Turn OFF the ignition.
  2. Remove the accelerator cable from the bracket.
  3. Remove the accelerator cable bracket bolt.
  4. Remove the accelerator cable bracket.
  5. Disconnect the ignition control module (ICM) harness connector.
  6. Remove the ICM retaining screws.
  7. Remove the ICM from the ignition coil housing.

To install:
  1. Install the ignition control module in the ignition coil housing.
  2. Install the ICM retaining screws. Tighten the retaining screws.
  3. Connect the ICM harness connector.
  4. Install the accelerator cable bracket.
  5. Install the accelerator cable bracket bolt. Tighten the retaining screws.
  6. Install the accelerator cable to the bracket.

2.2L (Ln2) Engine
  1. Remove the air cleaner outlet from the air cleaner.
  2. Remove the ICM electrical connectors (1) and spark plug wires (2).
  3. Remove the ignition coils bolts (3).
  4. Remove the ignition coils and ICM assembly.
  5. Installation is the reverse of the removal procedure.

2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accelerator cable from the hold down clip.
  3. Remove the cruise control cable, if applicable.
  4. Remove the bolt from the fuel line retaining clip.
  5. Disconnect the 11-pin harness connector for the ignition control module (ICM).
  6. Remove the bolts from the ignition coil and the ICM assembly-to-camshaft housing.
  7. Remove the ignition coil and ICM assembly from the engine.
  8. Remove the screws that retain the housing to the cover.
  9. Disconnect the coil harness connector from the ICM.
    CAUTION When removing the housing from the cover, make sure the ground strap stays in place.
  10. Remove the housing from the cover.
  11. Remove the screws that retain the ICM to the cover.
  12. Remove the ICM from the cover.

    9f8592c.jpg
    Fig. Removing the ICM from the camshaft cover

To install:

CAUTION DO NOT wipe grease from the module or coil if the same module is to be replaced. If a new module is to be installed, a package of silicone grease will be included with the module. Spread the grease on the metal face of the module and on the cover where the module seats. This grease is necessary for module cooling.
  1. Install the ICM to the cover.
  2. Install the screws that retain the ICM to the cover.
  3. Install the ground strap, if necessary.
  4. Connect the ignition coils connector to the ICM.
    CAUTION When installing the housing to the cover, make sure the ground strap stays in place.
  5. Install the housing to the cover.
  6. Install the screws that retain the housing to the cover.
  7. Install the spark plug boots and the retainers to the housing, if necessary.
  8. Install the ICM assembly to the engine while carefully aligning the spark boots to the spark plug terminals.
    CAUTION The ICM cover bolts must be installed using isolator washers with the rubber side facing down.
  9. Install the bolts that retain the ICM assembly to the camshaft housing after coating the bolt threads with LOCTITE, or equivalent. Tighten the bolts to 16 ft. lbs. (22 Nm).
  10. Connect the ICM 11 pin harness connector.
  11. Install the bolt to the fuel line retainer clip.
  12. Install the accelerator cable into the hold down clip.
  13. Install the cruise control cable, if applicable. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 05, 2010 | 2000 Chevrolet Blazer

1 Answer

No spark Power to coil New wires and new coil


Usually the ignition controll module or pickup coil. Your local auto parts store should be able to test the module for you.

Nov 05, 2009 | 1986 Volkswagen Golf

1 Answer

How do I change an ignition coil on a V6 1997 Grand Am?


Removal Procedure
  1. Remove all the electrical connectors at the ignition control module.
  2. Note position of spark plug wires for installation
  3. Remove the spark plug wires from ignition coils.
  4. Remove the screws securing coil assemblies to ignition control module.
  5. Disconnect coils from ignition control module. Installation Procedure
    1. Install the coils to ignition control module.
    2. Install the screws and tighten to 4-5 Nm (36-44 lb. in.) .
    3. Install the fasteners securing assembly to engine and tighten to 8 Nm (70 lb. in.) .
    4. Install the spark plug wires as noted during removal.
    5. Install the electrical connectors to the ignition control module
  6. Hope this Helps !

Sep 30, 2009 | 1997 Pontiac Grand Am

1 Answer

No spark at coil


check and clean the points if it has them. under the rotor in the cap

Jun 03, 2009 | 1983 Volkswagen Rabbit Pickup

1 Answer

Timing the cams and crank with a belt


  1. Note: Electronic Ignition engine timing is entirely controlled by the PCM. Electronic Ignition engine timing is NOT adjustable. Do not attempt to check base timing. You will receive false readings.

The CKP sensor is used to indicate crankshaft position and speed by sensing a missing tooth on a pulse wheel mounted to the crankshaft. The CMP sensor is used by the COP Integrated EI System to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The PCM uses the CKP signal to calculate a spark target and then fires the coil pack(s) to that target shown in Figure 51. The PCM uses the CMP sensor not shown in Figure 51 on COP Integrated EI Systems to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The coils and coil packs receive their signal from the PCM to fire at a calculated spark target. Each coil within the pack fires two spark plugs at the same time. The plugs are paired so that as one fires during the compression stroke the other fires during the exhaust stroke. The next time the coil is fired the situation is reversed. The COP system fires only one spark plug per coil and only on the compression stroke.

    The PCM acts as an electronic switch to ground in the coil primary circuit. When the switch is closed, battery positive voltage (B+) applied to the coil primary circuit builds a magnetic field around the primary coil. When the switch opens, the power is interrupted and the primary field collapses inducing the high voltage in the secondary coil windings and the spark plug is fired. A kickback voltage spike occurs when the primary field collapses. The PCM uses this voltage spike to generate an Ignition Diagnostic Monitor (IDM) signal. IDM communicates information by pulsewidth modulation in the PCM.
  1. The PCM processes the CKP signal and uses it to drive the tachometer as the Clean Tach Out (CTO) signal.

2.5L V6

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by a pulse former within the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition timing is determined by the powertrain control module in response to engine operating conditions based on stored data tables or maps. Once ignition timing has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 5, cylinders 4 and 3 and cylinders 2 and 6) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This ensures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
---------------------------------------------------------------
2.0L 4 cynder

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition angle is determined by the powertrain control module in response to engine operating conditions. Once ignition angle has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 4 and cylinders 3 and 2) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This make sures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
------------------------------------------------------------------------------------
Integrated Electronic Ignition System The Integrated Electronic Ignition (EI) System consists of a crankshaft position (CKP) sensor, coil pack(s), connecting wiring, and PCM. The Coil On Plug (COP) Integrated EI System uses a separate coil for each spark plug and each coil is mounted directly onto the plug. The COP Integrated EI System eliminates the need for spark plug wires but does require input from the camshaft position (CMP) sensor.
----------------------------------------------------------------------------------------

Apr 05, 2009 | 1998 Ford Contour

1 Answer

I have just had a maf sensor and throttle body put on my suzuki vitara 1997 2ltr petrol v6 engine as I had trouble with it jerking while driving.It still wont run properly it has no power to go up...


No power when going up hill could be a plugged catalytic converter or fuel filter. A bad ignition control module will act up when the engine gets hot and not energize the coils so they can provide spark to the spark plugs. There could also be a bad coil. The ticking could be a bad coil or spark plug wire that is shorting and arcing. If you take a spray bottle with some water and lightly mist the coils and spark plug wires with the engine running in the dark (outside at night) you will see the arcing. Autozone will test your ignition control module and coils for free.

Regards,

Tom

Dec 02, 2008 | Suzuki Vitara Cars & Trucks

Not finding what you are looking for?
2001 Volkswagen Golf Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...